Dynamic range compression
Last updated 8 min readTags:MixingDynamicsCompression
Learn how dynamic range compression works, what its controls do, and how to set a compressor for vocals, bass, drums and full mixes.
Dynamic range compression reduces level differences in audio by turning down louder moments. You can use it to keep a vocal audible, even out bass notes or change the impact of a drum hit.
Compression also changes how a performance feels. Too much can flatten its expression or soften the attacks that give it energy. Start with a specific aim, then judge the result at a matched listening level.
How compression works
A conventional downward compressor reduces gain when the level it detects exceeds a threshold. Its ratio determines how strongly it reduces level changes above that threshold. Attack and release control how quickly the gain reduction changes.[1]
For example, take a hard-knee compressor with a threshold of −18 dBFS and a ratio of 4:1:
| Measurement | Level |
|---|---|
| Input | −10 dBFS |
| Input above the threshold | 8 dB |
| Output above the threshold, at 4:1 | 2 dB |
| Output before make-up gain | −16 dBFS |
| Gain reduction | 6 dB |
This describes the compressor's settled response. A brief peak may pass at a higher level because of the attack setting.
Compression can reduce peaks and leave room to raise the overall level with make-up gain. Quieter details then become louder too. Compression and the subsequent gain increase work together; gain reduction alone turns the signal down where it acts.
The main compressor controls
Many compressors expose these controls. Some hardware designs and plug-ins fix certain settings or adjust them automatically.
| Control | What it changes | What to listen for |
|---|---|---|
| Threshold | The detected level above which gain reduction is called for | Whether the compressor responds to the notes or phrases you want to control |
| Ratio | How strongly levels above the threshold are compressed | Whether loud moments still stand out too much, or have become too restrained |
| Attack | How quickly gain reduction increases | The initial impact of a note, drum hit or consonant |
| Release | How quickly gain reduction recovers | Whether the sound recovers naturally or swells and dips audibly |
| Make-up gain | The output level after compression | Whether the processed and bypassed versions sound equally loud |
| Knee | How gradually compression develops around the threshold | Whether the transition into compression is noticeable |
Threshold, ratio and knee work together. A soft knee spreads the transition across a range of levels, which can include levels below the stated threshold. A hard knee has a defined change in the input-to-output curve at the threshold.[2]
Threshold and ratio: how much control do you need?
A lower threshold usually means more of the signal is compressed. A higher ratio usually means stronger reduction once compression is active.
Neither setting tells you how the result will sound on its own. A high ratio that catches occasional peaks may be less noticeable than a low ratio acting throughout a performance.
Watch the gain-reduction meter to see when the compressor acts. Constant reduction can be appropriate for sustained sounds or deliberate levelling. It does not automatically mean the threshold is too low.
Attack: preserve or reduce the initial impact
A faster attack can reduce the sharp beginning of a drum hit or picked note. A slower attack leaves more of that beginning intact while reducing the sound that follows.
Attack is a response rate, rather than a pause before anything happens. A 20 ms setting does not mean the first 20 ms pass completely untouched. Timing definitions and response curves vary between compressors, so identical settings can sound different.[3]
If a snare loses its crack, try a slower attack. If a picked bass note has an excessive spike, try a faster one. Compare within the mix, where the effect on impact is easier to judge.
Release: how does the sound recover?
A shorter release lets gain recover sooner. This can make the decay of a drum or the end of a note more prominent. Very short settings can also introduce distortion.
A longer release keeps gain reduction active for longer. It may smooth the level, but it can also reduce the next note before that note has had a chance to stand out. Auto-release modes adjust recovery according to the incoming material.[3]
For separate drum hits, try a release that lets the compressor recover substantially before the next hit. For a sustained vocal or bass part, continuous reduction may sound more natural.
Pumping means you can hear the level rise and fall as the compressor works. On a drum bus, cymbals might dip with each kick and swell afterwards. Keep that movement if it suits the track; adjust the release or reduce compression if it distracts.
Make-up gain: compare at the same loudness
Use make-up gain to bring the processed version close to the perceived loudness of the bypassed version. Then switch between them. Auto make-up gain can provide an estimate, but it may still need adjustment.[3]
Compare the same passage at the same monitoring level. Check whether the vocal is steadier or the drums have the impact you wanted. A louder output can make that judgement harder.
How to set a compressor
- Name the problem. For example: “The louder bass notes overpower the kick.” If only one or two notes cause trouble, edit their clip gain or automate their level first.
- Choose a passage with both loud and quiet moments. A setting that works on one sustained note may fail elsewhere.
- Start with a moderate ratio. Try 2:1 or 3:1 for straightforward level control. Lower the threshold until the troublesome moments trigger clear gain reduction.
- Adjust attack and release. Listen to the start of each note and the recovery between notes. Change one control at a time.
- Match the output loudness and bypass. Check whether the original problem has improved and whether the performance still has the expression you want.
- Check the whole track in context. Listen through quieter and louder sections. Revise the settings if the compressor responds badly to a different part of the arrangement.
These are starting points for an audition. There is no required amount of gain reduction for a good mix. If the uncompressed version works better, leave the compressor bypassed.
Compression on vocals, bass and drums
| Source | Possible aim | Useful listening check |
|---|---|---|
| Vocals | Keep loud words under control without losing expression | Are words easier to follow? Have breaths become distracting, or consonants too soft? |
| Bass | Reduce unwanted differences between notes | Does the bass hold its place against the kick? Does each note retain a clear start? |
| Drums | Reduce sharp peaks or emphasise the contrast between attack and decay | Has the hit gained the intended weight, or lost its impact? |
| Drum bus | Change how the grouped drums rise and fall | Do cymbals and room sound move naturally around the kick and snare? |
| Mix bus | Make a small change to the dynamics of the whole mix | Does the chorus still lift? Does a loud kick turn down too much of the rest of the mix? |
If a whole phrase is too quiet, level automation may be the more direct fix. If one instrument disappears because another occupies the same frequencies, inspect the arrangement and EQ as well.
Parallel compression
Parallel compression blends a compressed version of a signal with its uncompressed version. It can bring out sustain and quieter details while retaining more of the original attack.[4]
Use a compressor's mix control, or send the source to a separate compressed return. Start with that return low and raise it until the added body suits the mix.
The blend still changes the dynamics, and it usually changes the loudness too. Match the listening level before deciding whether it is an improvement.
Compression, limiting and clipping
| Process | Main action |
|---|---|
| Compression | Reduces level changes according to its threshold, ratio and timing |
| Limiting | Uses strong gain reduction for peak control; a brickwall limiter is designed to enforce an output ceiling |
| Clipping | Cuts or rounds off waveform peaks beyond a level |
| Normalisation | Applies a fixed gain change to meet a peak or loudness target, without changing the internal level relationships |
Limiting is related to compression, but a high ratio alone does not guarantee a firm ceiling. Attack behaviour and the limiter's design matter. Ableton's manual, for example, describes separate Standard, Soft Clip and True Peak modes for its Limiter.[4]
Choose the process for the job. Compression can steady a performance or reshape its impact. A limiter can control the final output peaks. Neither is compulsory on every track.