Dynamic EQ: what it is and when to use it
Last updated 6 min readTags:MixingEQDynamics
What dynamic EQ does, when to choose it over static EQ or multiband compression, and how to set a band without dulling the sound.
Dynamic EQ changes the gain of an EQ band in response to a detector signal. It can cut an unwanted frequency region when it becomes prominent, then ease the cut when it subsides.
For example, a vocal may sound balanced in the verse but harsh on louder chorus phrases. A permanent upper-midrange cut might soften the chorus and leave the verse dull. A dynamic cut can reduce the harsh phrases while making little or no change to the quieter ones.
How dynamic EQ works
A dynamic EQ band has a frequency, width and gain setting, much like static EQ. Its dynamic controls determine how that gain changes over time.
In a typical downward-cut setup, the detector measures energy around the chosen frequency. As that energy exceeds the threshold, the band applies more reduction, up to the permitted amount. The cut eases as the detector level falls.
Common controls include:
| Control | What it changes |
|---|---|
| Frequency and Q | The centre frequency and width of the adjustment |
| Threshold | The detector level at which processing begins |
| Range | The permitted amount of dynamic cut or boost |
| Attack | How quickly the adjustment responds |
| Release | How quickly it recovers |
| Sidechain source | The signal that triggers the adjustment |
Some plugins set the threshold or timing automatically. Others let you choose a detector frequency range independently of the EQ band. Check which controls your plugin exposes.
Dynamic EQ can boost as well as cut. This guide concentrates on cuts for occasional harshness, boom or masking.
When to choose dynamic EQ
Listen for when the unwanted sound occurs before choosing a processor.
| What you hear | A useful starting point |
|---|---|
| The same tonal problem whenever the part plays | Static EQ |
| Harshness or boom on particular phrases, notes or hits | Dynamic EQ |
| One troublesome word or isolated event | Clip gain, an edit or automation |
| A tonal change throughout a particular section | EQ automation |
| One instrument obscures another when they overlap | Arrangement changes or sidechain-triggered processing |
| A broad frequency range needs sustained dynamics control | Multiband compression or a broad dynamic EQ band |
These are starting points. A dynamic band cannot identify a bad sound by itself; its detector responds to level. If desirable notes trigger the cut as strongly as troublesome ones, automation may be more precise.
Dynamic EQ or multiband compression?
A conventional multiband compressor divides the signal into frequency bands and changes the level of each band. A dynamic EQ changes an EQ filter's gain, often with a bell or shelf shape.
Dynamic EQ is convenient for a specific resonance or harsh region. Multiband compression is often useful when you want to control the dynamics of a wider range, such as the low end of a drum bus. Their uses overlap: a wide dynamic shelf can make a broad adjustment too.
Neither tool is automatically more transparent. The amount of processing, timing and filter design matter more than the label.
How to set a dynamic cut
Take a vocal that becomes harsh on loud phrases. Start with one band on the vocal track.
1. Find the troublesome region
Compare a harsh phrase with a comfortable one. Identify the frequency range that becomes excessive.
If you sweep a temporary boost to locate it, keep the boost and listening level modest. An exaggerated boost can make almost any frequency sound unpleasant. Return the gain to zero before setting the dynamic cut.
A spectrum analyser can support what you hear, but a visible peak is not sufficient reason to cut.
2. Set the width and maximum cut
Choose a band wide enough to cover the harsh region. An excessively narrow cut may miss part of it; an excessively wide cut may remove useful presence.
As a practical starting point, try a maximum reduction of about 2 dB. This is a trial setting, not a target. Adjust it to the recording.
3. Adjust the threshold
Lower the threshold until the harsh phrases receive useful reduction. Then play a quieter phrase. It should retain its tone.
If both passages become dull, reduce the range or raise the threshold. If the plugin uses an automatic threshold, adjust its available sensitivity and range controls instead.
4. Adjust the timing
Start with automatic timing if available. Otherwise, listen for whether the cut catches the harshness and releases before the next phrase needs its presence back.
An attack that is too slow may miss the problem. A release that is too long may dull the following word. Very fast settings can sound rough, particularly on low-frequency material.
5. Check in the mix
Compare processed and bypassed playback at a similar perceived loudness. Check the whole vocal, not just the harsh phrase.
The successful setting reduces the distraction without leaving the vocal thin, dull or less intelligible. If you cannot hear a worthwhile improvement, bypass the band and reconsider the cause.
Using another track as the trigger
An external sidechain lets one track trigger an EQ adjustment on another.
For example, place a dynamic EQ on the bass and send the kick to its sidechain input. Set a cut where the bass obscures the kick. The bass then receives a temporary reduction when the kick triggers the detector.
Check the routing and detector settings in your DAW and plugin. Adjust the release so the bass recovers naturally between hits. Excessive reduction can make its tone change with every kick.
Common mistakes
Treating every peak as a fault. Strong harmonics are part of an instrument's sound. Cut a peak because it causes an audible problem.
Assuming continuous activity means failure. A band can remain active while varying its reduction. Compare it with a static cut and keep the version that sounds better.
Changing the input level afterwards. With a fixed threshold, upstream gain changes alter when and how strongly the band responds. Recheck the settings after changing earlier processing.
Fixing one instrument on the master. A dynamic cut across the full mix affects every instrument in that region. If you have the individual tracks, try the correction on the source first. See mastering EQ for work on a finished stereo mix.
Confusing dynamic EQ with automatic EQ. Dynamic EQ describes how a band responds during playback. Automatic EQ describes how settings are selected. A processor can use either or both.
Further reading
- FabFilter Pro-Q help: dynamic EQ, for detector options, range and automatic controls.
- Waves: how and when to use dynamic EQ, for vocal and external-sidechain examples.
- iZotope: multiband compressors versus dynamic EQs, for the differences between the two processors.