Skip to content

Types of EQ: what they do and when to use them

Send feedback

Last updated 7 min readTags:MixingEQEqualizationFundamentals

Understand parametric, graphic, dynamic, linear-phase and analogue-style EQ, with practical examples of when to use each.

For most mixing tasks, start with your DAW’s parametric EQ. It gives you control over where an adjustment sits, how wide it is and how much you boost or cut.

Other EQs suit particular jobs. A graphic EQ offers fixed frequency bands. A dynamic EQ responds to changes in level. A linear-phase EQ changes the phase behaviour of the processing. An analogue-style EQ recreates aspects of a hardware design.

These labels overlap. One plug-in can be parametric, dynamic and linear-phase. Here is what each term means and when it matters.

EQ types at a glance

Term What it describes Useful when you need to…
Parametric Adjustable frequency, gain and bandwidth Make precise corrections or broad tonal changes
Semi-parametric Adjustable frequency and gain, usually without a separate bandwidth control Shape tone with fewer controls
Graphic Gain controls at fixed frequencies Adjust a playback system or make changes at known frequency bands
Dynamic Band gain that responds to signal level Reduce a problem that comes and goes
Linear-phase A processing mode that preserves relative phase between frequencies EQ related signals without adding frequency-dependent phase differences
Analogue-style Hardware, or a plug-in based on a hardware design Use its particular curves, controls or added colour

Shelves, bells and high-pass filters describe the shape of an adjustment. They are often available within the same EQ.

Parametric and semi-parametric EQ

A parametric EQ lets you adjust three main settings on a bell band:

  • Frequency: where the boost or cut is centred.
  • Gain: how much you boost or cut.
  • Q or bandwidth: how narrow or broad the adjustment is.

A higher Q produces a narrower bell. A lower Q produces a broader one. See what is equalisation? for the basic controls and filter shapes.

Parametric EQ suits both detailed corrections and broad changes. You might use a narrow cut for a persistent ringing note, or a broad cut if a guitar sounds too thick through the low mids. The controls let you match the adjustment to what you hear.

A semi-parametric EQ usually lets you choose the frequency and gain but has no separate bandwidth control. Its width may be fixed or may change with the gain setting. This is common on simpler channel EQs. The terminology varies, so check the available controls.

Graphic EQ

A graphic EQ has a row of gain controls, usually sliders, at fixed centre frequencies. You can boost or cut each band, but you generally cannot move its centre frequency or adjust its width independently.

Graphic EQs are common in live sound and playback-system adjustment. The fixed bands make familiar changes quick to find. For a narrow resonance in a recording, a parametric EQ usually gives you more control over the exact frequency and width.

The sliders give a rough indication of the tonal adjustment. Their positions do not show the exact combined response, because neighbouring filters overlap.

Shelving and tilt EQ

A shelf changes a broad range at one end of the spectrum. A low shelf boosts or cuts the bass; a high shelf boosts or cuts the treble. The response changes gradually around the selected frequency, then settles towards the chosen gain.

A tilt EQ changes the balance around a pivot frequency. Turn it towards the treble and it raises the highs while lowering the lows; turn it the other way for the reverse effect.

Use a shelf when one end of a track needs adjustment. Use tilt when you want to change its overall balance with one control. Neither is a precise tool for an isolated ringing frequency.

Shelves can be bands inside a parametric EQ. Some plug-ins, such as Ableton’s EQ Eight, offer several filter shapes within one processor.

Static and dynamic EQ

A static EQ keeps the same curve until you change its settings. It suits a tonal problem that remains fairly consistent throughout a part.

A dynamic EQ changes a band’s gain in response to signal level. For example, a vocal may sound balanced in quiet phrases but become harsh when the singer pushes harder. A static cut could dull the quiet phrases. A dynamic cut can reduce the harsh range mainly when it becomes prominent.

The controls vary. Some dynamic EQs provide manual threshold, attack and release settings; others adjust some of these automatically. Many also accept an external sidechain, so another track can trigger the adjustment. FabFilter’s dynamic EQ documentation gives an example of these options.

For a harsh vocal, try this:

  1. Find the offending range by listening in the mix.
  2. Add a dynamic bell cut over that range.
  3. Adjust its threshold and maximum reduction so it acts mainly on the harsh phrases.
  4. Check that quieter words still sound natural.

Dynamic EQ and multiband compression overlap in use. Dynamic EQ typically changes the gain of selected EQ bands; a conventional multiband compressor divides the spectrum into ranges and processes their levels separately. Designs vary, however. Neither the product name nor the use of crossovers tells you whether a processor will audibly change an idle signal. Some multiband designs avoid static phase changes in their default mode.

Choose dynamic EQ when the required correction varies with the performance. For a consistent tonal adjustment, static EQ is usually simpler.

Minimum-phase and linear-phase EQ

Most conventional EQs change phase as well as level. The phase shift varies with frequency. This behaviour is often called minimum-phase, and it is a normal part of many analogue and digital EQ designs.

Linear-phase EQ preserves the relative phase between frequencies by delaying the whole signal equally. That delay adds latency. It can also produce pre-ringing, an effect before a transient that may soften a drum’s attack. The amount depends on the filter settings and implementation. FabFilter’s processing-mode guide explains these trade-offs.

Phase behaviour deserves particular attention when you blend an EQ’d signal with a related signal. For example, a filtered parallel drum bus combines with the dry kit. Frequency-dependent phase shifts can change how the two add together.

A linear-phase mode may help in that situation, provided the paths are time-aligned. Compare modes with the dry and processed signals playing together. Listen for changes in the kick’s weight and attack.

For ordinary track EQ, the default mode is a sensible starting point. Linear-phase is also optional in mastering EQ; it is not a mark of higher quality.

Analogue-style EQ

Analogue-style plug-ins reproduce aspects of hardware equalisers. These may include broad curves, stepped frequency choices, interactions between controls and, in some models, saturation or noise.

An analogue-style EQ may sound different because its curve differs from another EQ’s curve, even when the knobs show the same values. Added colour depends on the model and settings. A vintage appearance does not tell you how much saturation it adds.

Use one when its controls or sound suit the part. Compare it at a similar output level so an increase in loudness does not decide the result for you.

Which EQ should you use?

What you hear Start with What to check
A persistent ringing frequency A narrow parametric cut The ring reduces without making the part thin
Harshness on occasional loud phrases A dynamic bell cut Harsh phrases soften while quieter ones retain their tone
Too much bass across the part A low shelf The bass is better balanced without losing necessary weight
Rumble below the useful notes A high-pass filter Rumble falls without weakening the instrument
A track that needs a broad tonal change A shelf or tilt EQ It sits better in the full mix
An unwanted change when parallel signals combine Compare phase modes and check alignment Weight and attack remain intact

Make the adjustment in context, then bypass it at a similar loudness. Keep it if it improves the mix. If the change is hard to judge, reduce its size or reconsider the frequency before reaching for another EQ.

Was this page helpful?

    Type to search titles, headings and summaries.