High-pass filters: what they do and how to set them
Last updated 6 min readTags:MixingEQLow End
Learn how to set a high-pass filter's cutoff and slope to reduce rumble and excess bass without making vocals, instruments or your mix sound thin.
A high-pass filter, also called a low-cut filter, reduces low frequencies while passing higher frequencies. In a mix, it can reduce microphone rumble, handling noise and unwanted bass from instruments or effects.
The aim is to remove low-frequency content you do not need while retaining the part's useful sound. There is no need to filter every track, and no single cutoff suits every vocal, guitar or bass.
Cutoff, slope and resonance
Three controls determine how the filter affects the sound.
Cutoff frequency
The cutoff marks a point in the filter's transition from passing sound to reducing it. It is not a boundary below which everything disappears.
For a Butterworth filter, the level at the cutoff is about 3 dB below the passband level. Other filter designs and resonance settings can give a different response. A filter set to 100 Hz may also reduce frequencies above 100 Hz, so a cutoff just below an instrument's lowest note can still reduce that note's weight. See MathWorks' Butterworth filter documentation for the technical definition.
Slope
Slope describes how quickly the level falls below the cutoff. It is measured in decibels per octave, or dB/octave. An octave down means half the frequency: 50 Hz is one octave below 100 Hz.
A 12 dB/octave filter eventually falls by roughly 12 dB for each octave down. A 24 dB/octave filter falls more steeply. These rates describe the response away from the cutoff; the curve bends through the cutoff region.
Gentler slopes reduce a wider range of nearby frequencies gradually. Steeper slopes make a sharper transition. Either can be appropriate, depending on how close the unwanted sound is to the sound you want to keep.
Resonance or Q
On many EQs, raising the filter's Q adds a boost near the cutoff. This can emphasise bass rather than simply remove it. Leave the filter at its default, non-resonant setting for ordinary clean-up, then adjust it if you want a tonal effect.
The available slopes and Q behaviour vary between EQs. For example, FabFilter Pro-Q's band controls include adjustable slopes, but Q is fixed at 6 dB/octave.
When to use a high-pass filter
Use one when you can identify low-frequency content that the part does not need:
- Rumble or handling noise: low thumps and vibration in a microphone recording.
- Excess bass from close microphone placement: directional microphones can emphasise low frequencies when the source is close, a behaviour called proximity effect.
- Unwanted low end in the arrangement: a guitar, pad or reverb may obscure bass notes without contributing useful depth of its own.
Microphone low-cut filters serve similar purposes; Shure's UC Wireless guide describes their use for low-frequency noise and excessive proximity effect.
Choose another treatment if the problem is more specific. A low shelf reduces bass by a chosen amount without continuing to cut more deeply at lower frequencies. It may suit a recording that needs less bass but still needs its low notes. A bell cut may suit a narrow boom. An isolated vocal plosive may need an edit or local gain reduction.
The equalisation guide explains these filter shapes.
How to set a high-pass filter
- Find the problem. Listen to the part in the mix. Briefly solo it if you need to identify rumble, spill or another unwanted sound.
- Start below the useful range. Choose a gentle slope, such as 6 or 12 dB/octave, with no resonant boost.
- Raise the cutoff slowly. Listen in the mix. When the part begins to lose useful body, lower the cutoff again.
- Adjust the slope if necessary. If unwanted low frequencies remain, compare a steeper slope. Revisit the cutoff too; the two controls work together.
- Bypass and compare. Check the lowest notes and a sparse section. Keep the filter if it solves the problem without an unwanted loss of body or attack.
This sweep method finds a useful starting point. If the noise overlaps the instrument's useful range, a filter may require too much compromise. Try editing, automation or a different EQ shape instead.
What to check on different sources
Vocals
Set the filter while the singer's lowest phrases are playing. A setting that suits a high chorus may remove too much from a low verse.
Listen for reduced rumble without a loss of vocal body. If only a few plosives cause trouble, treat those moments separately rather than raising the cutoff for the whole performance.
Kick and bass
These parts often need the frequencies that other tracks can spare. Filter them only for a reason, such as unwanted energy below their useful range or a deliberate change in tone.
On bass, check the lowest note actually played in the song. On kick, compare both the initial hit and the low-frequency decay. A filter can change either, even when its cutoff looks low on the display.
Guitars, keys and pads
Judge these parts by their role in the arrangement. An acoustic guitar accompanying a voice may need much of its low end. The same guitar in a dense band arrangement may benefit from less bass.
Check exposed passages as well as busy ones. If one setting cannot suit both, automate the EQ rather than accept a thin sound throughout.
Overheads and multi-mic recordings
Check overheads with the close drum microphones playing. A conventional high-pass filter changes phase as well as level, so filtering one microphone can alter how it combines with the others.
Listen for changes in the kick and snare's weight when you bypass the filter. The soloed overhead sound cannot tell you whether the combined drum sound has improved.
Reverb returns
Low-frequency reverb can make bass notes harder to distinguish. A high-pass filter on the return can reduce this while leaving the dry instrument unchanged. Keep enough low end for the intended sense of space.
Can steep filters affect transients?
They can, though the result depends on the filter design, cutoff and source. Conventional steep filters can produce more pronounced phase changes near the cutoff and alter the shape of a drum hit or bass attack. Phase change is not automatically an audible fault.
Linear-phase EQ preserves relative phase, but introduces latency and can produce pre-ringing: a short sound before a transient. It is not an automatic improvement for low-cut filtering. FabFilter's processing-mode documentation explains these trade-offs; the linear-phase EQ guide covers their practical use.
Choose the slope by the result. A steep filter may preserve more useful bass when unwanted rumble lies just below it. A gentler filter may give a smoother tonal change.
Check the whole mix
Several individually reasonable cuts can leave a mix short of warmth. If the arrangement starts to sound thin, compare it with the high-pass filters bypassed together.
Use headphones or speakers that reproduce the affected bass range. Small speakers are useful for checking the overall balance, but may hide the low frequencies you are trying to judge.
A spectrum analyser can show what changed. It cannot establish whether the removed bass was musically useful. Likewise, a full-mix energy measurement cannot identify which individual track needs filtering.
On a mix bus or finished stereo file, check particularly carefully: the filter affects every instrument. Use mastering EQ only where the combined result needs correction. If the concern is low-frequency stereo width, assess that separately with the sub stereo width guide.
Keep a high-pass filter when the unwanted low end is reduced and the part still sounds right in the arrangement. If bypass sounds better, revise the setting or remove the filter.