Skip to content

Sub stereo width

Send feedback

Last updated 4 min readTags:MixingStereoLow End

Understand Sonalix’s sub stereo width reading, check whether your bass loses weight in mono, and find the source before changing your mix.

Sub stereo width describes how much the left and right channels differ in the lowest part of your mix. In Sonalix, it focuses on frequencies below 100 Hz.

Use the reading to decide whether your bass needs a mono check. A higher reading calls for closer listening; it does not, by itself, prove that the mix needs correction.

Why check the sub-bass separately?

A full-mix stereo correlation reading describes the relationship between the left and right channels across the spectrum. It can obscure differences within a smaller frequency range. The sub stereo width reading focuses on the bass that a full-mix figure may overlook.

When a stereo signal is summed to mono, some frequencies can become quieter through phase cancellation. You may hear less weight in the kick or find that certain bass notes become much weaker. Complete cancellation is the extreme case, rather than the inevitable result of stereo bass.[1]

How to interpret the reading

Read the result alongside what you hear:

Result What to check
Lower sub stereo width Check that the bass has the weight and balance you want. A low reading alone does not establish this.
Higher sub stereo width Compare the mix in stereo and mono. Listen for bass notes or kick hits that lose weight.
Very little sub-bass in the track Consider whether this frequency range matters to the arrangement before making changes.

Some mixes contain deliberate stereo bass. The practical question is whether the important low-frequency content survives mono playback. Avoid forcing the reading lower when the bass already sounds consistent.

The metric also has limits. It does not tell you whether the bass is too loud, identify the responsible instrument, or rule out cancellation between separate kick and bass tracks. Use it with the stereo correlation and tonal balance summary.

What to listen for

Choose a passage with sustained bass notes and clear kick hits. Switch your monitoring between stereo and mono, with the perceived listening level kept as consistent as possible.

Listen for:

  • Bass notes that become disproportionately quieter in mono.
  • A kick that loses its low-frequency weight.
  • Changes in bass level that affect some notes more than others.

Some change in the mix is expected when the stereo image collapses. Concentrate on whether the kick and bass remain in balance, rather than whether stereo and mono sound identical.

Use headphones or monitors that reproduce the relevant bass frequencies. A phone or small laptop speaker is a poor test of sub-bass loss because it may reproduce little of that range.

Find the source before processing the master

If the bass weakens in mono, bypass likely causes one at a time:

Possible source First check
Stereo bass synth Compare the patch with unison spread, chorus or stereo detuning reduced.
Stereo widening plug-in Bypass it, then check whether it offers a way to exclude low frequencies.
Reverb or delay return Mute the return. If it causes the problem, try filtering unnecessary bass from that return.
Multiple recordings of the same source Check their timing and polarity relationship.

Make these comparisons in the full mix as well as in solo. Keep the change only if it improves the balance you heard failing in mono.

For example, if a bass synth becomes weak in mono but recovers when its chorus is bypassed, adjust the chorus or keep it on a separate upper-frequency layer. This addresses the source of the loss.

When to narrow the low end

If the problem remains, try reducing the stereo width of the sub-bass on the affected track or bus. A multiband imager can do this within a selected frequency range.

Another option is a high-pass filter on the Side channel of a mid/side EQ. Mid/side processing separates the sum of the left and right channels from their difference. Filtering low frequencies from the Side channel reduces stereo difference in that range.[2][3]

Try a cutoff around 80–100 Hz as a starting point. Adjust it by ear; the cutoff and filter slope determine how much of the bass changes. Keep the upper bass wide if it contributes usefully to the sound.

Narrowing the bass cannot restore content that already cancels in the mono sum. Removing Side information leaves the Mid sum unchanged in an ideal mid/side processor. If a bass note is already missing from that sum, return to the source or the processing that caused the cancellation.[2]

Linear-phase processing is optional. It can introduce pre-ringing, so compare processing modes if the kick or bass attack changes.[4]

Check the result

Compare the adjusted mix with the original in both stereo and mono. Check the passage that first revealed the problem, then listen through the rest of the track and analyse the new export.

Keep the adjustment if the bass survives mono playback more consistently and the stereo mix still sounds right. A lower width reading is useful evidence, but the listening comparison determines whether the change was worthwhile.

Sources

  1. Sonarworks: Fixing phase issues
  2. iZotope: What is mid/side processing?
  3. FabFilter Pro-Q: Stereo options
  4. FabFilter Pro-Q: Processing mode

Was this page helpful?

    Type to search titles, headings and summaries.