Skip to content

Linear-phase EQ: how it works and when to use it

Send feedback

Last updated 4 min readTags:MasteringEQEqualization

Understand linear-phase EQ, its latency and pre-ringing, and when to compare it with minimum-phase EQ in mixing and mastering.

Linear-phase EQ boosts and cuts frequencies while preserving their relative phase. It delays the whole signal by the same amount across frequencies. The drawbacks are added latency and possible pre-ringing, which can make drum hits sound less distinct.

Start with a conventional minimum-phase EQ for everyday mixing. Try linear phase when an EQ adjustment causes an unwanted change in the way related signals combine, such as a snare close mic and overheads.

Linear phase versus minimum phase

Most conventional EQs use minimum-phase filters. These change phase around the frequencies you adjust, as well as changing their level. This behaviour is normal in analogue EQs too.

For modest bell and shelf adjustments, the phase change is often difficult to hear. Steep filters can have a more obvious effect on the shape of a transient, the brief attack at the start of a sound. Phase changes can therefore matter even on a single track.

Linear-phase EQ avoids that frequency-dependent phase change. It does not preserve the original waveform exactly; the frequency balance still changes, and the filtering can introduce ringing.

Property Minimum-phase EQ Linear-phase EQ
Relative phase Changes with the filter settings Preserved
Added latency Can be zero; depends on the plug-in Required for practical plug-in implementations
Filter ringing After the transient Before and after the transient
First use to consider Everyday track and bus EQ EQ on related signals that will be combined

The two drawbacks

Latency

A linear-phase EQ delays playback. Your DAW normally compensates for the plug-in's reported delay to keep tracks aligned, provided delay compensation is active and supported by the routing.

That compensation does not remove the wait when you play or sing through the plug-in. Use a low-latency mode while recording or monitoring live input.

The delay varies by product and setting. For example, FabFilter Pro-Q 4 lists about 70 ms for its lowest linear-phase resolution at 44.1 kHz, rising to about 1.5 seconds at its highest. Those are product-specific figures, rather than a general range for all EQs. See its processing-mode documentation.

Pre-ringing

Pre-ringing is a short oscillation before a transient. It may sound like a faint tone or a brief swell just before a drum hit. The attack may seem less immediate.

Narrow bands, large gain changes and steep filters make it more likely to be audible. Pay particular attention to low-frequency adjustments on kick drums and bass. Gentle settings may produce no noticeable problem.

FabFilter's linear-phase EQ guide includes audio examples. Listen for the sound before each hit, rather than judging only the change in bass level.

When to try linear-phase EQ

Parallel processing

Suppose you duplicate a bass track, EQ the copy and blend it with the original. A minimum-phase EQ changes the phase relationship between the two paths around the adjusted frequencies. Their combination may then sound thinner or more coloured than you intended.

Compare linear phase in that blend. Check that delay compensation keeps both paths aligned. Linear phase avoids adding frequency-dependent phase shift, but the EQ still changes how much of each frequency the processed path contributes.

Recordings made with several microphones

A snare close mic and overheads contain versions of the same drum hit. EQ on one microphone can change how those recordings combine. iZotope's guide uses multiple drum microphones to explain this problem.

Compare modes with the other microphones playing. Judge the snare's attack and body in the full kit, then check the mix in mono. Choose the version that suits the recording.

Linear-phase EQ does not correct existing microphone timing or polarity problems. Nor does a difference in arrival time necessarily need correction. Listen before moving recorded tracks.

Mid/side EQ and mastering

Try both modes when different EQ settings on the mid and side channels produce an unwanted change in the stereo image. Check the centre, the width and the mono version. Linear phase does not prevent the stereo balance from changing when you alter mid or side levels.

A stereo master is also a reasonable place to compare modes, but mastering alone is no reason to select linear phase. For broad tonal adjustments, begin with the mode you normally use. The mastering EQ guide covers those decisions.

How to compare the modes

  1. Choose a revealing passage. Use clear drum attacks or a section where the parallel blend sounds wrong.
  2. Keep the EQ settings the same. Switch processing mode within one plug-in if possible. Allow playback to settle after the switch.
  3. Match the output level. A louder version can seem better even when the tonal change is less useful.
  4. Listen in context. Check the parallel blend, full drum kit or complete mix. Solo the track briefly if you need to identify pre-ringing.
  5. Keep the version you prefer. If the difference is negligible, use the lower-latency option.

If linear phase improves the blend but weakens the attack, reduce the gain change, widen the band or try a gentler high-pass filter. Compare again before adding further processing.

Was this page helpful?

    Type to search titles, headings and summaries.