Quality tier: how to read your score
Last updated 4 min readTags:MasteringAnalysis
Understand Sonalix's quality tier, the four measurements behind the score, and what to check before changing your mix.
Sonalix's quality tier summarises four measurements: loudness, true peak, crest factor and stereo correlation. The score starts at 100. Deductions place your track in one of four tiers, shown as a badge in your report.
Use it to decide which readings deserve a closer look. The score cannot tell you whether the vocal sits well, the bass is balanced or the track feels finished.
What the tiers mean
| Tier | Score | Report label | Badge colour |
|---|---|---|---|
| 3 | 75–100 | Release-ready with minor revisions | Indigo |
| 2 | 55–74 | Competitive for streaming | Green |
| 1 | 35–54 | Approaching commercial quality | Amber |
| 0 | 0–34 | Below industry standard | Red |
These are Sonalix's assessment labels. A high tier means fewer deductions under its scoring rules. It does not certify release readiness or guarantee acceptance by a distributor.
Read the individual measurements even when your score is high. A single problem can leave the track in Tier 3: an 18-point true-peak deduction alone produces a score of 82.
How the score is calculated
Each of the four measurements can reduce the score. Within each metric, only the largest applicable deduction is used. Deductions from different metrics are then added together.
| Measurement | Range | Points deducted |
|---|---|---|
| Distance from −14 LUFS | More than 8 LU | 40 |
| More than 5, up to 8 LU | 25 | |
| More than 3, up to 5 LU | 12 | |
| 3 LU or less | 0 | |
| True peak | Above −0.3 dBTP | 18 |
| Above −1.0, up to −0.3 dBTP | 8 | |
| −1.0 dBTP or lower | 0 | |
| Crest factor | Below 5 dB | 25 |
| 5 dB to below 8 dB | 12 | |
| 8 dB or higher | 0 | |
| Stereo correlation | Below 0.5 | 15 |
| 0.5–0.97 | 0 | |
| Above 0.97 | 8 |
The loudness calculation uses the absolute distance from −14 LUFS. For example, −20 LUFS and −8 LUFS are both 6 LU away, so each receives a 25-point deduction.
Loudness range (LRA) and five-band spectral energy do not contribute to this score. They provide additional context elsewhere in the report and in AI coaching.
Example calculation
Consider a track with these readings:
| Measurement | Reading | Points deducted |
|---|---|---|
| Integrated loudness | −8 LUFS | 25 |
| True peak | −1.2 dBTP | 0 |
| Crest factor | 7 dB | 12 |
| Stereo correlation | 0.75 | 0 |
The score is 100 − 25 − 12 = 63, which falls in Tier 2.
This explains the score; it does not prescribe a change. Listen for unwanted compression or lost transient detail before adjusting the dynamics.
What to check when points are deducted
Loudness
Check whether the level suits the track and its intended use. Sonalix measures distance from −14 LUFS in either direction, so a quiet mix awaiting mastering can lose points as well as a loud master.
Spotify uses −14 LUFS for its Normal playback setting and recommends it in its mastering guidance. Its guidance also addresses masters above that level. Treat Sonalix's reference as a scoring choice, rather than a universal release requirement. Spotify's loudness guidance
True peak
True peak estimates the highest level of the reconstructed waveform, including peaks between samples. A deduction is a reason to check peak headroom and the delivery guidance for your destination. The score itself does not prevent clipping. AES explanation of true peaks
Crest factor
Crest factor is the difference between peak and RMS level, expressed in decibels. A low value can prompt a check for flattened transients, pumping or unwanted distortion. It cannot establish the cause by itself.
If you hear a problem, compare the track with less compression or limiting. Match playback levels so that the louder version does not win simply because it is louder.
Stereo correlation
Check the mix in mono and listen for important parts that weaken or disappear. A reading below 0.5 does not, by itself, prove harmful cancellation. Negative correlation is a more direct warning of that risk. Apple's correlation meter guide
A reading near +1 means the channels are very similar. A narrow or mono recording may be intentional; avoid widening it merely to recover points.
How to use the tier in a mix review
Start with the measurements that lost points. Check the relevant passage by ear, make one change, then export and analyse the revision. Compare the sound as well as the readings.
A higher score confirms that fewer deductions apply. A useful improvement may leave the tier unchanged, especially if it concerns balance or tone rather than one of the four scored measurements.
For a mix going to a mastering engineer, follow their delivery instructions. There is no need to reach Tier 2 before handing it over, or to add limiting solely to raise the score.
The tier is calculated separately from AI coaching, so it does not depend on a coaching response. Use the badge as a quick summary, the individual readings to investigate, and listening to judge the result.