Double tracking: what it is and how to use it
Last updated 5 min readTags:Production TechniquesMixingRecording
Double tracking layers two performances of the same part. Learn how to record tight doubles, balance vocals and guitars, and check the result in mono.
Double tracking means recording the same musical part twice, then playing both takes together. Small differences in timing, pitch and delivery can make a vocal or instrument sound fuller. Pan the takes apart and those differences can also create stereo width.
The second take should follow the first closely enough to sound like the same part. How closely depends on the effect you want: subtle reinforcement, a wide guitar sound, or an obvious doubled voice.
What makes a double different from a copy?
A fresh performance contains differences that a straight copy does not. A singer holds a vowel slightly longer. A guitarist strikes a chord a little earlier. Those changes give the combined sound its doubled character.
An identical copy of a mono recording, at the same position on the timeline and with the same processing, adds no new performance information. Pan the original fully left and the copy fully right at equal levels, and both channels still carry the same signal. The result remains centred rather than wider.[1]
Panning is optional with real doubles. Two takes can sit in the centre for a thicker sound, or sit apart for width. Double tracking does not require a wide stereo image.
How to record a useful second take
1. Choose where the double belongs
Decide which section needs the extra layer. You might double only the chorus, a guitar riff or a few important words. A whole-song double can work, but it need not stay audible throughout.
2. Record the part again
Use a separate track and monitor the first take at a comfortable level. Keep the notes, rhythm and phrasing close to the original.
For vocals, pay particular attention to consonants, breaths and word endings. For guitars, check pick attacks, chord lengths and muted stops. Differences at these points are often more distracting than small variations within a sustained note.
3. Correct the distracting differences
Replace weak phrases or choose a better section from another take. Edit obvious timing problems if necessary.
For a blended double, the two performances should sound like one part with some natural variation. If you hear two separate word endings or a staggered chord attack, check that passage. Avoid aligning every detail automatically; an extremely tight edit may reduce the character you wanted.
4. Set the level and panning
Start with the second take quiet, then raise it until the effect suits the part. A low double can reinforce a lead vocal without sounding like a second singer. Similar levels make the doubling more obvious.
Choose the panning in the full mix. Wide separation may suit rhythm guitars; a centred or narrowly panned double may suit a lead vocal.
5. Compare at a similar loudness
Mute and unmute the double, then adjust the combined level so the doubled version is roughly as loud as the single take. Listen for a useful change in texture or width. Extra volume alone can make the doubled version seem better.
Common uses
| Part | Starting point | What to listen for |
|---|---|---|
| Lead vocal | Keep the main take centred and blend a quieter double beneath it. | The words remain clear and the vocal sounds fuller. |
| Chorus vocal | Introduce a double for the chorus. For a centred lead with doubles on both sides, record two additional takes. | The chorus gains weight or width without losing the main voice. |
| Rhythm guitar | Record two takes and try one fully left, the other fully right. | Chord attacks and stops remain tight across both speakers. |
| Backing vocal | Record additional takes of each harmony as needed and spread them across the stereo image. | The voices blend without blurred lyrics or uneven tuning. |
These are starting points. A lead guitar can suit obvious doubling, while a sparse vocal may sound better on its own. With bass, judge whether the extra take adds useful texture or makes the note attacks and low end less clear.
When to use automatic double tracking
Automatic double tracking, or ADT, creates a doubling effect from one recording. A processed version plays alongside the original, with a short, varying delay and associated pitch changes.[2]
ADT is useful when you cannot record another take, or when you prefer its particular sound. It also gives you control over the effect after recording. A real double captures another performance; ADT derives its variation from the existing one.
Start with a restrained effect level. Listen for unwanted pitch movement, an audible echo or a hollow tone when the original and processed signals combine. The separate automatic double tracking guide covers the method in more detail.
Check the result in mono
Switch your monitoring to mono and listen to the doubled part within the mix. Stereo width will disappear; that is expected. Check whether the part still has the tone, level and clarity it needs.
A delayed copy can cause comb filtering when combined with the original: some frequencies reinforce each other while others cancel. This can produce a hollow or swishing sound. ADT therefore needs a mono check; the Reel ADT manual includes a mono monitoring control for this purpose.[2]
Two separately recorded performances do not have the same fixed relationship as a recording and its delayed copy. They can still sound uneven or blurred together, so check both the performances and any effects.
If the mono result sounds poor, mute the double and then bypass its effects to locate the cause. For ADT, adjust the effect level, delay or modulation and check again. For recorded doubles, revisit mismatched phrasing or an unsuitable take. Narrower panning alone does not remove the timing relationship that causes comb filtering.
Is the double improving the part?
Listen in the full arrangement. Keep the double if it adds the weight, texture or width you intended while preserving the important words and attacks. If only one phrase benefits, use it there. If the part becomes harder to follow, lower the double, edit it or leave it out.
Sources
- Sonarworks: Three Chances for a Wide Mix, on double tracking and why identical copies do not create stereo width.
- Waves / Abbey Road Reel ADT user guide, on ADT's delay and pitch variation, phasing and mono monitoring.