Skip to content

5-band energy: how to read your mix’s tonal balance

Send feedback

Last updated 5 min readTags:MixingFrequencyTonal Balance

Understand the five frequency bands in your mix, what their readings suggest, and how to check tonal balance before making EQ changes.

Five-band energy analysis summarises the frequency content of a mix in five broad regions: sub, low-mid, mid, presence and high. It gives you a quick view of the balance between bass, midrange and treble.

Use it to decide where to listen more closely. A high reading in one band does not, by itself, mean that anything needs fixing.

The five frequency bands

These are the ranges used in this guide. Other analysers may use different names and boundaries.

Band Range What to listen for
Sub 20–100 Hz Deep bass and the lowest part of the kick. Check whether the low end has enough weight or sounds excessive.
Low-mid 100–500 Hz Bass body and warmth in voices and instruments. Check whether parts sound full or become difficult to distinguish.
Mid 500 Hz–4 kHz Much of the vocal and instrumental detail. Check whether important parts sound clear, recessed or overly forward.
Presence 4–8 kHz Consonants, sibilance and percussion attack. Check whether these sound defined or piercing.
High 8–20 kHz Upper cymbal detail, hiss and the brightness often described as ‘air’. Check whether the top end suits the track.

Instruments extend across several bands. A vocal is not confined to the midrange, and a kick drum can contribute both deep bass and high-frequency attack.

How to read the values

Read the band values together. Their relationship is more useful than any one number in isolation.

For example, suppose the low-mid band reads −12 dB and the mid band reads −18 dB. The low-mid reading is 6 dB higher. This describes a difference between two broad regions; it does not tell you to cut 6 dB with an EQ.

For readings expressed on the same dB scale, a less negative value is higher: −12 dB is higher than −18 dB. The meaning of either value depends on the analyser’s reference level and calculation method. Do not read it as a LUFS value, a peak level or a percentage of the mix’s total energy.

The bands do not need to be equal. A bass-heavy electronic track and a sparse acoustic recording can have quite different balances, and both can sound right.

What the patterns can suggest

The readings can direct your attention to a broad area. Confirm any suspected problem by listening.

Pattern What to check
Sub stands well above low-mid Does the kick or bass overpower the arrangement? Is there unwanted rumble?
Low-mid stands above mid Do the bass, guitars, keys or vocals obscure one another? Does the mix sound congested?
Presence stands above mid Are vocal consonants, cymbals or percussion attacks uncomfortable?
High sits well below presence Does the mix lack upper-frequency detail, or does the arrangement simply contain little of it?

A broad average cannot establish the cause. A strong presence reading might come from cymbals, a vocal or several instruments together. A low high-band reading might suit a deliberately dark recording.

There is no single band difference that proves a mix is muddy, harsh or dull. Treat an automated flag as a reason to investigate, rather than an instruction to process the audio.

How to use the result

  1. Listen for a specific problem. Describe what you hear, such as ‘the bass obscures the vocal’ or ‘the cymbals sound piercing’.
  2. Check the relevant band. See whether the reading is consistent with that impression.
  3. Compare with a suitable reference. Choose a track with a similar arrangement and intended sound. Match playback loudness for listening, and use the same analysis settings for both files.
  4. Find the source in the session. Check individual tracks and buses before applying EQ to the whole mix.
  5. Make a small change and compare. Keep it if the mix sounds better at a comparable listening level.

A low-mid excess, for instance, might call for a lower guitar level, a different bass sound or a targeted EQ cut. The five-band result cannot choose between those fixes on its own.

What the measurement leaves out

Five bands give you a broad summary. They cannot show every narrow resonance or reveal exactly when a problem occurs. An average across a whole track may also conceal differences between a sparse verse and a dense chorus.

A detailed frequency spectrum can show peaks and dips within a band. A peak still needs context: it may be an unwanted resonance, or simply a prominent musical note.

Check how the analyser handles stereo, too. If it combines the left and right channels into mono before measurement, phase cancellation can change the result. A mono reading may differ from what you hear in stereo.

Is ‘energy’ the same as loudness?

No. Band energy and perceived loudness are different measurements. Converting spectral values to decibels does not make them a perceptual loudness measurement.

The calculation also matters. An average of spectral magnitudes, an average of dB values and a sum of spectral power produce different results. Band widths affect comparisons as well, particularly when a tool sums power across each band.

Compare readings from the same analyser and settings. Use the tonal balance summary for an overview, then return to the audio before deciding what to change.

Further reading

Was this page helpful?

    Type to search titles, headings and summaries.