Skip to content

How to read a spectrum analyser

Send feedback

Last updated 8 min readTags:MixingFrequencyEQ

Learn what a spectrum analyser shows, how slope and resolution affect the display, and how to use it to check your mix.

A spectrum analyser shows the level of the different frequencies in your audio. Bass appears on the left, treble on the right. It can help you locate a boomy bass note, investigate harshness or compare your mix with a reference track.

The shape depends on the analyser’s settings as well as the audio. Two analysers can show different slopes for the same track. Before you make an EQ decision, check how the display is set up and listen to the passage concerned.

What the display shows

The horizontal axis shows frequency in hertz (Hz). It usually uses a logarithmic scale, so each octave takes up the same width. The distance from 100 to 200 Hz is the same as the distance from 1 to 2 kHz.

The vertical axis shows level in decibels (dB). A higher point means a higher measured level at that frequency. It does not necessarily mean that frequency sounds louder; our hearing is more sensitive to some frequencies than others.

Most analysers use a fast Fourier transform (FFT) to divide short sections of audio into frequency bins. The display may show a rapidly changing spectrum, a slower average or the highest level reached in each bin.

One instrument can appear across much of the display. A bass note has a fundamental and harmonics above it; its sound extends beyond the bass region. A bump in the full mix therefore does not identify which instrument caused it or prove that two parts are masking each other.

Why the same track can look different

Slope or tilt

Many analysers apply a visual tilt that raises the treble relative to the bass. This changes the display without changing the sound.

Pink noise provides a useful example. It has equal energy per octave. On an FFT display with equal-width frequency bins and no tilt, its average level falls by about 3 dB per octave. On a display that sums energy into octave or third-octave bands, it appears approximately flat.

Pink noise display Expected average shape
Equal-width FFT bins, no tilt Falls by about 3 dB per octave
Same FFT display, +3 dB/octave tilt Approximately flat
Same FFT display, +4.5 dB/octave tilt Rises by about 1.5 dB per octave
Energy summed into third-octave bands, no tilt Approximately flat

Both Voxengo SPAN and FabFilter Pro-Q document a default tilt of 4.5 dB per octave. Check your own settings, particularly if you use saved presets.

A flat line is not a target for a good mix. Its meaning depends on the display, and the appropriate frequency balance depends on the music.

Resolution

FFT size affects how closely spaced frequencies can be distinguished. Larger FFT sizes provide finer frequency detail but analyse a longer section of audio. Short events are less precisely located in time.

At a sample rate of 48 kHz:

FFT size Bin spacing Audio per analysis window
2,048 samples About 23.4 Hz About 42.7 ms
8,192 samples About 5.9 Hz About 170.7 ms

Bin spacing is not a guarantee that two nearby tones will appear as separate peaks. The analysis window, smoothing and relative levels also affect the result.

Use a larger FFT size when you need to examine bass notes or narrow low-frequency peaks. A smaller size may be more useful for following quick changes.

Averaging, release and peak hold

These controls affect how the display behaves over time, but they do different jobs:

  • Averaging combines measurements over time. It makes the overall balance easier to judge, though brief events may become less visible.
  • Release or decay controls how quickly the displayed level falls. A slow release is not necessarily a true average.
  • Peak hold or maximum retains the highest level reached at each frequency. Those peaks may have occurred at different moments.

Names vary between plug-ins. Check the manual before comparing an average with a held or maximum trace.

Smoothing and vertical range

Smoothing reduces fine detail so broad shapes are easier to see. Use less smoothing to examine a narrow peak. Some analysers offer octave-based smoothing; others use different controls.

The vertical range also changes the appearance. A small level difference looks much larger when the screen covers fewer decibels. Keep the range consistent when comparing tracks.

How to use an analyser when mixing

1. Choose a passage and listen

Start with a specific observation: “the bass booms on this note” or “the vocal becomes harsh in the chorus”. Loop that passage.

You can also use an analyser for a routine balance check, particularly when your speakers reproduce little deep bass. Treat any unexpected shape as something to investigate. The shape alone is not a reason to change the mix.

2. Set up the display

For the overall mix, place the analyser after the processing you want to assess. Keep speaker or headphone correction outside that measurement if you want to inspect the mix itself.

Use an averaged view with moderate smoothing for broad balance. For a brief event or narrow peak, reduce smoothing and choose suitable resolution. Note the tilt and vertical range.

3. Look at broad balance, then individual peaks

A broad rise in the low mids may correspond to the muddiness you hear. Check the levels of guitars, keys and bass before reaching for EQ. Several parts may be contributing to the same region.

A narrow peak needs a closer listen. Does it occur on every note, on one bass note or only when a particular drum hits? Solo likely sources to locate it, then judge any adjustment with the full mix playing.

A peak that stays at one frequency may be a resonance, a sustained note or a repeated drum tone. A peak that follows the melody may be perfectly natural, but one note can still be too loud. Movement alone does not tell you whether a peak needs treatment.

For more detail, see resonances and frequency masking.

4. Compare with a suitable reference

Choose a reference with a similar arrangement and intended sound. Compare equivalent passages, such as a full chorus against a full chorus.

Match their playback loudness and use identical analyser settings, including channel mode. A whole-track LUFS match is a useful starting point, but the selected passages may still differ in loudness.

Look for broad differences: more low-mid energy, less upper treble or a stronger sub-bass region. The reference gives you context; you do not need to reproduce every peak and dip.

5. Make one change and compare

Adjust a level, change an arrangement or try an EQ cut. Match the playback level before and after, then listen in context.

Keep the change if it improves the mix. Check the display to see where the change occurred, rather than whether the line looks smoother.

Common shapes and what to check

What you see What to check
Broad low-mid rise Do guitars, keys, vocals or bass overlap too heavily? Try level changes first.
Narrow peak at a fixed frequency Which source produces it? Does it ring or dominate audibly?
Large low-frequency peak on each kick Is the kick too loud, or is this appropriate for the arrangement? Check whether it drives excessive limiting.
Little energy below 30–40 Hz Does the music need deeper bass? Many arrangements do not.
Sharp upper-frequency cut-off Check the source file and filtering. Lossy encoding is one possible cause, but the graph alone cannot establish it.

An analyser inside your DAW measures the digital signal at its insert point. It does not show how your room changes the sound at your listening position. That requires an acoustic measurement with a microphone.

Reading a spectrum in a Sonalix report

A static spectrum summarises the analysed audio. It is useful for checking broad frequency balance, but a whole-track view can obscure a brief harsh phrase or a bass note that booms once.

Use the report to choose what to investigate in your DAW. Loop the relevant passage and use a live analyser when you need more detail. See frequency response curve for the report chart and five-band energy for the band summary.

Frequently asked questions

What should a good mix look like on a spectrum analyser?

There is no single correct shape. The arrangement, instruments and intended sound all matter. Compare suitable reference tracks through the same analyser settings, then judge the audible differences.

Is a spectrum analyser the same as an EQ curve?

No. The analyser shows the frequency content of the audio. An EQ curve shows the gain changes applied by the filters. Many EQ plug-ins display both together.

Can a spectrum analyser show stereo problems?

Some offer left/right or mid/side views, which can reveal differences in frequency content. Use a correlation meter and listen in mono to investigate phase cancellation. Check the analyser’s channel mode too; a mono sum can cancel content that remains audible in stereo.

Sources

Was this page helpful?

    Type to search titles, headings and summaries.