Skip to content

The frequency spectrum: sub bass to air

Send feedback

Last updated 6 min readTags:MixingFrequencyFundamentals

Learn the main frequency ranges in a mix, what they sound like, and how to find the source of muddiness, harshness or a weak low end.

The frequency spectrum describes the frequencies present in a sound and their levels. Low frequencies give us bass; high frequencies give us treble. The usual reference range for human hearing is about 20 Hz to 20 kHz, though individual hearing varies.

In mixing, names such as low mids, presence and air describe parts of that range. They give you a starting point when a track sounds muddy, harsh or dull.

The main frequency ranges

These boundaries are approximate. Guides divide the spectrum differently, and a sound's character does not change abruptly at a particular frequency.

Region Approximate range Common sounds and qualities Possible signs of excess
Sub 20–60 Hz Deep bass, lowest kick frequencies, rumble Overpowering low end
Bass 60–250 Hz Kick and bass body, low notes of guitars and keys Boominess, bloat
Low mids 250–500 Hz Body and warmth in voices and instruments Muddiness, boxiness
Mids 500 Hz–2 kHz Much of the character of vocals, guitars and keys Honkiness, a nasal sound
Upper mids 2–4 kHz Vocal clarity, pick attack, drum attack Harshness, listening fatigue
Presence 4–8 kHz Consonants, cymbal detail, sibilance Piercing treble, sharp “s” sounds
Air 8–20 kHz Cymbal shimmer, breath, high-frequency ambience Hiss, excessive brightness

These descriptions are listening clues. A mix can contain plenty of low-mid energy and still sound clear. It can also sound harsh because of one brief sound, rather than a persistent excess across a whole region.

Sub: 20–60 Hz

Sub gives deep bass its weight and can be felt as well as heard. Kick drums, bass instruments and unwanted rumble can all contribute here.

Small speakers may reproduce very little of this range. Do not boost it simply because you cannot hear it on your usual speakers. Check on suitable headphones or a system with reliable bass reproduction, and compare with a familiar reference track.

Bass: 60–250 Hz

This range supplies much of a track's low-end body. Kick and bass often overlap here, alongside lower notes from guitars, keyboards and other instruments.

If the low end sounds indistinct, listen to the kick and bass together. Their levels, note lengths and timing may need attention before EQ. Too little energy here can leave a mix sounding thin.

Low mids: 250–500 Hz

Low mids give many sounds warmth and body. They can also become crowded when several parts play together.

A muddy or boxy sound may come from overlapping instruments, a single recording or a resonance. Find the source before cutting. Removing too much from every track can leave the whole mix hollow.

Mids: 500 Hz–2 kHz

Vocals, guitars, keys and many other instruments have important tonal detail here. This range remains audible on small speakers, so it matters when you check whether parts can still be heard on a phone or laptop.

An excess can sound honky or nasal. Heavy cuts can make instruments sound distant or remove too much of their character.

Upper mids: 2–4 kHz

Upper mids contribute to speech clarity and the attack of guitars and drums. Our hearing is particularly sensitive around this part of the spectrum, so small changes can be conspicuous.

If a vocal struggles to come through, check what competes with it here before adding a boost. Too much can make a mix tiring to hear.

Presence: 4–8 kHz

Presence includes consonant detail, cymbal attack and much vocal sibilance. Sibilance can also fall outside this range, depending on the voice and recording.

If only certain syllables sound sharp, a de-esser or dynamic EQ may suit the problem better than a permanent treble cut.

Air: 8–20 kHz

Air describes the high-frequency detail in cymbals, breath and ambience. A gentle lift can make some recordings sound more open, but it can also bring up hiss or make cymbals too prominent.

Hearing sensitivity varies considerably at these frequencies. Compare with reference tracks at a similar playback level before deciding that a mix needs more air.

Why instruments span several frequency ranges

A bass guitar does not occupy only the bass region. Its low notes have fundamentals in the bass or sub range, while harmonics extend into the mids and beyond. Those harmonics contribute to its tone and can keep the notes audible on small speakers.

The same applies to other instruments. A kick can have low-frequency weight and a high-frequency click. A vocal can have low-mid body, upper-mid clarity and breath in the air range.

This is why instrument frequency charts are approximate. The note, playing style, recording and processing all affect the spectrum. For more on the relationship between fundamentals and harmonics, see distortion and saturation.

How to find a frequency problem

  1. Describe what you hear. Is the mix boomy, muddy, harsh or dull? Does it happen throughout the track or only in one section?
  2. Choose a likely region. Use the table as a starting point. Check neighbouring frequencies if the first area does not explain it.
  3. Check the source. Lower or mute likely contributors one at a time. Listen to the result in the full mix.
  4. Try one small change. Adjust a level, shorten a note, change the arrangement or use EQ. Choose the change that addresses what you heard.
  5. Compare before and after. Keep the perceived loudness similar. Check that the change improves the problem without weakening another part of the track.

For example, suppose a chorus sounds muddy after doubled guitars and a pad enter. Lower the pad first. If the vocal becomes clearer, try leaving the pad quieter or reducing some of its low mids. Then check whether the chorus still has enough body.

A permanent cut across the whole mix would also affect the verse, even if the verse already sounds balanced.

If you use an EQ sweep to locate a resonance, keep the boost modest and the playback level comfortable. A large, narrow boost can make almost any frequency sound unpleasant. Judge the proposed cut after removing the search boost.

Check your listening conditions

Playback level changes the balance you hear, particularly the apparent strength of the bass. Make most tonal decisions at a consistent, comfortable level, then check more quietly.

Your room and listening position can also exaggerate or weaken bass notes. If a problem changes substantially when you move, compare on headphones before altering the mix.

A frequency response curve can show where energy is concentrated. It cannot tell you whether that balance suits the music. Use a reference track with a similar sound and arrangement, at a comparable perceived loudness.

How Sonalix's five bands compare

Sonalix groups the spectrum into five measurement bands. Their boundaries differ from the seven descriptive regions above.

Sonalix band Range Regions covered
Sub 20–100 Hz Sub and lower bass
Low-mid 100–500 Hz Upper bass and low mids
Mid 500 Hz–4 kHz Mids and upper mids
Presence 4–8 kHz Presence
High 8–20 kHz Air

A high Sub reading could reflect a prominent kick, a sustained bass part or unwanted rumble. The band value alone cannot identify the source or tell you that it needs correcting.

See 5-band energy for help with the measurements, or tonal balance summary for their interpretation in a report.

Further reading

Was this page helpful?

    Type to search titles, headings and summaries.