Skip to content

Per-metric severity: what the ratings mean

Send feedback

Last updated 4 min readTags:AnalysisAI Coaching

Understand Sonalix’s Good, Caution, Warning and Critical ratings, what each audio metric tells you, and what to check before changing your mix.

Per-metric severity is the rating beside each measurement in your Sonalix report: Good, Caution, Warning or Critical. It shows how that value compares with the range Sonalix uses for that metric.

Use the rating to decide what to check. A measurement outside the range deserves attention, but it does not establish what caused it or whether a change will improve the music.

What the four ratings mean

Rating Colour How to read it
Good Green The value falls within Sonalix’s preferred range. No concern is flagged by this measurement.
Caution Amber The value falls outside the preferred range. Check whether it suits the track.
Warning Orange The value warrants a closer check. Read the explanation and listen for the possible problem.
Critical Red The value falls in Sonalix’s most severe category. Investigate it before your next export.

A Good rating does not confirm that the whole mix sounds good. Equally, a Critical rating is a Sonalix classification; it does not automatically mean a distributor will reject the file.

How the ratings are assigned

Sonalix compares each measured value with fixed thresholds for that metric. The same value receives the same rating while those thresholds remain unchanged.

These comparisons do not account for genre or artistic intent. A deliberately narrow stereo image or a quiet acoustic recording may fall outside the preferred range and still sound right.

Read the value, its explanation and any benchmark note together. A small change can cross a rating boundary without making a substantial audible difference.

What to check for each metric

Integrated loudness: the track’s overall loudness

Integrated loudness, measured in LUFS, describes loudness across the track. It does not tell you whether the mix is balanced or whether its transients sound clear.

If loudness is flagged, consider the intended release and compare the track with suitable references at a matched listening level. Listen for distortion or loss of impact before adding more limiting.

Streaming normalisation is a playback level adjustment. A louder master being turned down does not, by itself, indicate a fault. Spotify’s Normal setting uses −14 LUFS; EBU R 128’s broadcast recommendation uses −23 LUFS. Neither establishes a universal Good range for music mastering.[1][2]

True peak: the estimated maximum waveform level

True peak, measured in dBTP, estimates the highest level of the reconstructed waveform, including peaks between samples.

If it is flagged, check your limiter ceiling and the exported file with a true-peak meter. Allow headroom for the intended delivery format. Spotify recommends peaks below −1 dBTP, or below −2 dBTP for masters louder than −14 LUFS.[1]

A true-peak warning identifies a headroom concern. It does not prove that audible distortion has occurred.

Crest factor: the gap between peaks and average level

Crest factor compares peak and average levels, conventionally with RMS as the average. A low value can accompany dense material or heavy compression and limiting. A high value can accompany prominent transients or a sparse arrangement.[3]

If it is flagged, listen to the attacks of drums and other percussive sounds. Compare your dynamics processing with a level-matched bypass. The number alone cannot tell you whether the track needs more or less compression.

Loudness range: variation across the track

Loudness range, or LRA, describes variation in short-term loudness over time. It measures a different aspect of dynamics from crest factor.[4]

A low LRA can suit a consistent arrangement. A higher LRA can suit a track with marked changes between sections. If it is flagged, listen through those transitions and consider whether the contrast serves the music.

Do not add compression merely to reduce LRA, or expand the track merely to raise it.

Stereo correlation: similarity between left and right

Stereo correlation describes how closely the left and right channels relate. A value near +1 indicates similar channels. Negative values can indicate a risk of cancellation when the channels are combined in mono.[5]

If it is flagged, listen in mono. Check whether important instruments lose level, change tone or disappear. A high positive reading can be appropriate for a narrow or mono recording; a brief negative reading does not necessarily indicate a problem.[5]

How to act on a rating

  1. Read the explanation. Identify the concern behind the badge.
  2. Check the context. Consider the arrangement, intended sound, release format and stage of production. An unmastered mix need not have the loudness of a finished master.
  3. Listen for evidence. Use a level-matched comparison, a reference track or a mono check as appropriate.
  4. Make a targeted change. Address the audible problem or delivery requirement you have identified.
  5. Export and analyse again. Check the new measurement and confirm that the change sounds better.

You do not need every badge to turn green. The useful outcome is a mix that sounds as intended and meets its delivery requirements.

Sources

  1. Spotify: Loudness normalisation
  2. EBU R 128: Loudness normalisation and permitted maximum level of audio signals
  3. iZotope: What is crest factor and why is it important?
  4. EBU Tech 3342: Loudness Range
  5. iZotope Ozone documentation: Correlation meter

Was this page helpful?

    Type to search titles, headings and summaries.