Skip to content

Master equalisation: how to EQ a finished mix

Send feedback

Last updated 7 min readTags:MasteringEQEqualizationMixing

Learn how to use mastering EQ, compare references at matched levels, choose suitable filters and recognise when a problem needs a mix revision.

Master equalisation, usually called mastering EQ, adjusts the frequency balance of a finished mix. It can reduce excess bass, soften a harsh upper midrange or add a little brightness before release.

The main constraint is that you are processing combined audio. A boost around 3 kHz may bring the vocal forward, but it also affects guitars, drums and anything else with energy in that range. Each adjustment needs to suit the mix as a whole.

Mastering EQ can correct problems or shape the sound to suit the music. Some mixes need very little; others need none.

What can mastering EQ change?

Mastering EQ is useful when the overall frequency balance needs attention. These are possible starting points, rather than settings to apply to every track.

What you hear An adjustment to try What to check afterwards
Bass overwhelms the rest of the mix A gentle low-shelf cut The kick and bass still have enough weight
The mix sounds thick or muffled A broad low-mid cut Vocals, guitars and snare retain their body
The upper midrange sounds harsh A small bell cut in the offending region Vocals remain clear and instruments keep their attack
The whole mix sounds dull A gentle high-shelf boost Cymbals, vocal sibilance and hiss stay under control
Harshness appears only in louder passages A dynamic EQ cut Quieter passages retain their brightness

These descriptions overlap. A mix may seem dull because it has too much bass, rather than too little treble. Try one change at a time and listen to its effect on the whole balance.

EQ cannot make deep sub-bass audible on a speaker that cannot reproduce it. If a bass part disappears on small speakers, its upper harmonics, arrangement or level may need attention in the mix.

How to EQ a master

1. Identify a specific problem

Listen to the full track before adding processing. Use speakers or headphones you know well, at a comfortable, consistent level. Room treatment and reliable monitoring make these judgements easier, but you can still cross-check decisions on familiar headphones.

Describe what you want to change: “the bass dominates the chorus” is more useful than “it needs to sound professional”. Check whether the problem runs through the track or appears only in particular sections.

If one instrument is responsible and you have the session, consider fixing it there. A master EQ adjustment may affect too much of the surrounding music.

2. Compare suitable references at matched loudness

Choose references with a similar arrangement, production style and intended sound. Compare equivalent sections, such as a full chorus against another full chorus.

Turn down a louder reference until its perceived loudness is close to your mix. Equal peak readings do not guarantee equal loudness. A louder track can seem fuller or clearer simply because of the level difference.

Listen for useful differences in bass weight, midrange clarity and treble. A reference is a guide; your track does not need an identical spectrum. Different instruments and arrangements produce different frequency balances.

3. Make one adjustment and level-match the result

For a broad tonal problem, start with a shelf or a broad bell filter. A lower Q gives a wider bell; a higher Q gives a narrower one.

Try a small gain change, perhaps 0.5–1 dB, then adjust by ear. This is a starting point, not a prescribed range. There is no universal 3 dB limit, and an audible improvement can be smaller than 0.5 dB.

For example, if the mix sounds too bass-heavy, try a low shelf around 100 Hz with a 1 dB cut. Adjust the frequency to suit the track. Listen for clearer vocals and less low-end dominance, while checking that the kick still has weight.

Compensate for any loudness change with the EQ's output gain, then compare the processed and bypassed versions. Keep the adjustment only if you prefer the balance at a similar listening level.

Larger moves deserve closer scrutiny. Ask whether the adjustment improves the whole mix, or merely makes one troublesome element less obvious.

4. Check the full track through the final chain

Revisit quiet passages as well as dense sections. A cut that clears a busy chorus may leave a sparse verse sounding thin. Automation or dynamic EQ may suit a problem that changes over time.

Listen with any downstream compression and limiting active. An EQ boost can change how hard those processors work, so the final result may differ from what you heard with the EQ alone. Recheck output level and true peak after the change.

Check on another familiar playback system and in mono. If the results disagree, investigate the speakers, headphones or room before making another correction. Two systems agreeing is useful evidence, but it is not proof that the balance is right.

Which type of EQ should you use?

Minimum phase or linear phase

A conventional minimum phase EQ is a suitable starting point for most mastering adjustments. Its phase response changes around the affected frequencies; this does not automatically make the result worse.

Linear phase EQ preserves relative phase relationships, with an overall delay. It can be useful when phase differences would cause problems, such as in some parallel processing arrangements. It also adds latency and can produce pre-ringing: a faint sound before a transient that may soften its attack.

Neither mode is inherently the most transparent in every case. Compare them if you hear a problem, particularly with steep filters or low-frequency processing.

Dynamic EQ

Dynamic EQ varies the gain of a frequency band in response to a detected signal level. It can reduce upper-mid harshness during loud passages without applying the same cut throughout the song.

Set the threshold and maximum cut so the processing responds when needed. Listen for unwanted dulling or changes to drum attack. Dynamic EQ still affects other sounds in the same band while it is active.

Mid/side EQ

Mid/side EQ processes the sum and difference of the left and right channels separately. It can adjust the tonal balance of shared and differing stereo information, but it does not separate instruments.

A centred vocal is usually prominent in the mid signal, alongside other centred sounds. Panned instruments can contribute to both mid and side. Treating “mid” as a vocal channel, or “side” as everything panned away from centre, leads to misleading decisions.

Check stereo balance and mono playback after any mid/side adjustment.

When should you return to the mix?

Return to the mix when the master EQ correction causes another problem. For example, a treble cut may tame an overly bright vocal but leave the cymbals and guitars too dull. The vocal track is then the more useful place to work.

A narrow cut can be appropriate for a specific resonance in a stereo file. Broad filters are not compulsory. Judge the audible result and the sounds affected, rather than deciding from bandwidth or gain alone.

If you only have the stereo file, you may need a compromise. Try the least intrusive correction and check it across the song. Neither mid/side EQ nor multiband processing can reliably isolate a source in every mix.

How to use an analysis report

A frequency analysis can draw attention to a region worth checking. It cannot establish the right tonal balance from the spectrum alone.

If a report flags strong low-mid energy, listen for masking or muddiness before cutting it. The energy may be appropriate for the arrangement. Make a measured adjustment, compare at matched loudness and keep it only if the music sounds better.

Further reading

Was this page helpful?

    Type to search titles, headings and summaries.