How to read your Sonalix mix report
Last updated 4 min readTags:AnalysisSonalix
What each part of your Sonalix mix report means, how to work through the recommendations, and where the measurements behind them are.
Your report is built in a fixed order: what to fix, how to fix it, and the measurements behind it. Every figure in it is measured from your file. The wording comes from fixed templates written for each kind of problem, so the same file with the same genre always gets the same report.
The overview
The top of the report names your file, its length and the genre you chose. Below that is a short paragraph that names the most important change first. If parts of the mix already measure well, they're listed under Already working. Leave those parts alone while you fix the rest.
Mix improvements
This is the main part of the report. Each card is one change, in order of priority, and there are never more than four. A report can also have no cards: No mix change is recommended means nothing that was measured calls for one.
Each card has the same parts:
| Part | What it tells you |
|---|---|
| Title | The problem, named by the part of the spectrum it affects, such as the low mids or the top end. A passage card also shows its time range. |
| Do this | The move to make, usually an EQ move on the mix bus, with its settings: the filter type, the frequency and the gain. |
| You'll hear | What should improve when the move works. |
| Check | When to keep the move, when to reduce it and when to undo it. |
| Step by step | The move as a numbered list for your DAW, with why it matters. |
| Troubleshooting | What to do if the move doesn't sound right. |
| Why this was flagged | The measurement behind the card, compared with the reference range. |
Make one change at a time. Compare it with the original at the same playback volume before you move to the next card. A louder version usually sounds better at first, whether or not it is.
The settings are a starting point, not a target. A mix-bus gain change is never more than 6 dB: a larger correction belongs on the individual tracks.
Kinds of card
- Tonal balance. A region of the spectrum sits above or below the range of released music. Regions run from the sub-bass to the top end; see how Sonalix measures your mix for their ranges. If you chose a genre, the comparison uses releases in that genre.
- Build-up. About half an octave collects too much energy, often heard as boom or mud.
- Resonance. A narrow frequency stands out from its neighbours, often heard as a ring or whistle. See resonances.
- Passage. A problem appears in one stretch of the track rather than throughout. The card gives the time range to listen to.
- Stereo. Part of the mix cancels when it is played in mono, one channel is silent, or the channels are out of phase. See stereo correlation.
Optional listening check
Some reports add a card marked Optional check. It isn't a fault: it asks you to compare something by ear, such as the mix with the limiter bypassed at matched volume. Skip it if you're happy with what you hear.
Export check
This compares the highest peak in your file with the export target, which is −1.0 dBTP by default. If the peak is above it, the check tells you how far to lower the export level. See true peak.
Measurements and method
The last section holds the figures behind the report. You don't need them to act on the recommendations.
- Tonal balance against the reference range. Each region of your mix, shown against the range of the reference releases.
- Level and stereo measurements. Each reading has a plain name with its technical name beside it, such as Overall loudness for integrated loudness in LUFS.
- Spectrum and loudness over time. The whole-track spectrum, and how loud each moment is.
- Measured, with no recommendation. Things that were measured and are worth knowing, but that don't need a change.
- How this report was made. What was checked, what wasn't assessed, and the limits of the method.
A report measures the file, not the music. It doesn't judge the arrangement, the performance or the balance between instruments: use your ears for those. For the exact figures that produce each card, see metric thresholds and target ranges. If your own meter shows a different reading, see why your DAW meter and Sonalix disagree.
Using the report
- Fix the cards in order, one at a time, and listen after each change.
- Export the revised mix and analyse it again. When a problem is fixed, its card no longer appears.
- Your reports are kept in your dashboard, so you can compare versions.
- Use Print or save as PDF to keep a copy outside Sonalix.