Skip to content

Home studio acoustics: what to fix first in a small room

Send feedback

Last updated 5 min readTags:MixingMonitoringAcoustics

Find a better position for your monitors and chair, work out why bass notes boom or disappear, and choose acoustic treatment for a small home studio.

If the bass returns when you lean forward, leave the mix alone for a moment. Play a track you know well and move your head again. If the same notes change level, start with the room.

Set up the monitors and chair before buying panels. If you have a measurement mic, take a reading before you move anything. Once you have found a better position, let the problem you can still hear guide the treatment.

Start with the monitors and chair

  1. Face down the length of the room. In a rectangular room, try placing the monitors at the short end, firing down the length of the room. Centre the setup between the side walls and keep the layout around the two monitors as similar as the room allows.
  2. Set up an equilateral triangle. Start with the monitors the same distance from each other as they are from your head. Put the tweeters near ear height and aim the monitors as the manufacturer recommends.
  3. Move the chair. Try sitting with your ears about 38% of the room length from the wall behind the monitors as a starting point, then try positions a little further forward and back. Stay centred left to right. Listen for the position where bass notes are most even.
  4. Change the distance from the wall. Move both monitors closer to or further from the wall behind them in small steps. Keep the left and right distances equal and follow the manufacturer’s clearance guidance, especially for rear-ported monitors. If voices still sound hollow, try moving the monitors up or forward to change the reflection from the desk.

Mark promising positions with tape. Compare them at the same playback level with a familiar track and a quiet bass sweep. Change one thing at a time so you can tell what made the difference.

Why some bass notes boom or disappear

Room modes are resonances set by the room’s dimensions. At a modal frequency, the bass can be strong in one spot and weak in another. Some resonances also make a note linger after it has stopped in the recording.

In a rectangular room, the first mode between two opposite surfaces is roughly 343 ÷ (2 × distance in metres). In a room 4 m long, 3 m wide and 2.5 m high, the first modes along those dimensions are about 43 Hz, 57 Hz and 69 Hz. The first length mode has a pressure minimum halfway between the front and back walls. That is one reason to try a seat away from the halfway point. The calculation gives you frequencies to check with a sweep. Several effects can overlap at the same frequency.

Boundary cancellation happens when a reflection from a nearby surface arrives out of phase with sound coming directly from the monitor. For the wall behind a monitor, the first dip is roughly 343 ÷ (4 × distance in metres), measured from the wall to the monitor’s front face. At 50 cm, that puts the dip near 170 Hz. If the dip shifts higher when you move the monitors closer to the wall, that reflection is a likely contributor. See phase cancellation and comb filtering.

Treat the problem that remains

Bass still rings

Try thick porous bass traps across the corners you can use. Corners offer space for deep absorption and an air gap behind a panel. Thin foam mainly absorbs higher frequencies and will do little for a deep bass resonance. If you rent, freestanding traps are an option.

Listen for whether the troublesome note dies away sooner. If you measure, look at the decay as well as the level. A bass note can still hang on after its peak has come down.

The centre of the stereo image sounds diffuse

Early reflections from the side walls, desk or ceiling can make a centred vocal sound less firmly placed. Check that the monitors are at equal distances and matched in level before adding treatment.

To find the side-wall reflection points, sit where you mix while someone slides a mirror along each wall. Mark the places where you can see either monitor. Try broadband absorbers, around 5–10 cm thick, over those areas and compare the same mono vocal before and after. A ceiling panel can address a strong reflection overhead.

Acoustic treatment changes what you hear inside the room. Soundproofing reduces sound transmission between rooms.

Measure the room and check your mixes

With a calibrated measurement mic and software such as Room EQ Wizard (REW), take a sweep of each monitor separately. Start with the mic where your ears normally are. Keep the sweep level and mic position the same when you compare speaker moves or treatment. When you test a new chair position, move the mic with it.

The frequency response shows where the level rises or falls. A waterfall plot shows which frequencies take longest to decay. Look for changes that hold up when you move the mic slightly within your usual listening area.

After positioning and treatment, monitor correction EQ can reduce a broad peak that persists around the listening position. Avoid boosting a deep cancellation dip. The reflected sound also gets louder, and the boost uses up headroom.

Keep a few familiar reference tracks on hand and compare at similar playback levels. If their bass sounds lean at the desk as well, check your mix on headphones before turning up the bass.

Sources

Was this page helpful?

    Type to search titles, headings and summaries.