Skip to content

What is mastering?

Send feedback

Last updated 4 min readTags:MasteringDelivery

Learn what mastering changes, which problems to fix in the mix, and how to master a finished track and check the export.

Mastering is the final stage of audio production. You listen to the finished mix, adjust its overall tone, dynamics or loudness where needed, then check the files you’ll send for release. For an EP or album, you also check how the songs sound in sequence.

Mixing gives you direct control over individual tracks. In stereo mastering, every change acts on the stereo mix. A high-shelf boost can brighten a dull mix, but it can also bring out the cymbals and vocal sibilance. If the vocal is the only thing that needs to come up, turn it up in the mix.

Which problems should you fix in the mix?

What you hear Where to start What to try
The vocal gets buried when the guitars come in Mix Ride the vocal level or bring down the guitars in that section.
One hi-hat hit is harsh Mix Turn down the hit or EQ the hi-hat.
The kick and bass mask each other Mix Adjust their levels or EQ them separately.
The whole track sounds a little dark, including on a second playback system Master Try a small, broad high-shelf boost and listen to what happens to the cymbals and vocal.
The choruses of two similarly arranged songs feel uneven in sequence Master Adjust their relative levels by ear and listen through the transition.

If you can point to the track or section that causes the problem, fix it there first. Even something you hear across the whole song can come from a single source. A bass part that’s too loud throughout can make the entire mix seem boomy.

How to master a finished mix

Use a separate session with your stereo mix and a released track you know well. Compare similar passages, such as chorus with chorus, and set their playback levels so they sound equally loud. Route the reference around your mastering plug-ins so you hear the reference as released. How to use reference tracks

  1. Listen before adding plug-ins. Play the mix through and describe what you hear in specific terms. “The whole chorus sounds darker than the reference” gives you something to check. If the mix already sounds right, you can move straight to the release checks.
  2. Try a small EQ move if the whole mix needs it. Start with a broad adjustment of around 1 dB. Match the processed and bypassed levels and listen again. If a brighter top end also makes the vocal esses jump out, back off the boost or revisit the mix. Master equalisation
  3. Use compression if there’s a reason for it. If loud hits make the mix feel uneven, try a low ratio and a decibel or two of gain reduction on the loudest passages. Match the output level and compare. Listen for a softer drum attack or for the rest of the mix dipping after each kick. If you prefer the bypassed version, take the compressor out.
  4. Set the loudness and check the peaks. If you want a louder master, set a true-peak limiter’s ceiling according to the delivery guidance, then raise the level into it. Compare with the limiter bypassed at the same perceived loudness. Back off if the snare loses its attack, the bass starts to distort or a loud section feels crowded. Playback normalisation can turn a loud master down, so chasing a higher meter reading may buy very little. Limiting · Loudness normalisation
  5. Export and listen to the exported file. Check the required format, sample rate and bit depth before rendering. Listen to the export from start to finish, including the first note and the full reverb or fade at the end. Check for clicks or distortion, measure integrated loudness and true peak, and confirm you’ve exported the correct version. True peak

What changes when you master an EP or album?

Put the songs in release order and listen through the transitions. A quiet opener can stay quiet. If two full-band tracks sit next to each other and one makes you reach for the volume control, adjust their relative levels and listen again. Check the spacing between tracks and whether the end of one song gives the next enough room. Integrated loudness readings can flag jumps worth hearing for yourself.

Can you master your own music?

Yes. Leave some time after the last mix revision, then listen on a second system you know. If the low end seems excessive only at your desk, check your monitoring before cutting bass from the master.

A mastering engineer brings an independent listen and a dedicated monitoring setup. That is particularly useful when you’re unsure how the mix will translate, when several songs need to work together or when the release has format-specific requirements. If your own master holds up against the mix at matched loudness and the exported file passes the delivery checks, you have a reasonable place to stop.

Was this page helpful?

    Type to search titles, headings and summaries.