What is gain staging? Five checks for a mix
Last updated 4 min readTags:MixingLevelsGain Staging
Learn where to adjust gain in your DAW, how to set plug-in input levels, and when turning down the master fader will fix clipping.
Gain staging means setting the signal level at each point in the chain, from the recording input to the final mix output. Where you change the level matters. Turn down a vocal before its compressor and you may get less gain reduction. Turn it down after the compressor and you get a quieter version of the same compressed vocal.
Use these five checks as you set up the session and revisit the relevant one when a level problem crops up. If the master meter is already in the red, start with the output check.
1. Leave room at the recording input
Ask the performer to play or sing the loudest passage and watch the input peak meter. For 24-bit recording, peaks around −12 dBFS are a sensible starting point. Leave more room if the performance is unpredictable. Check that the quieter parts are clear of distracting noise.
If the input clips, turn down the gain before the point that overloads and record another take if you can. Clip gain can turn down a clean recording that came in loud. It cannot restore peaks clipped during recording. See Sonalix’s guide to clipping.
2. Set the level going into the first effect
Use clip gain on a loud sample or recording. For a virtual instrument, use its output control or put a gain plug-in immediately after the instrument, before the audio effects. Play the loudest passage and check the level at the input of the first effect. Your usual track meter may show the level after processing or after the fader.
You can leave a quiet pad quiet if it sits well. A snare can have much higher peaks than a pad at the same RMS level because its energy is concentrated in short hits. Use the peak meter to check headroom, and listen in context before adjusting either track. See peak vs RMS for the difference between those readings.
3. Set the plug-in input and compare at matched loudness
Set the input level for the response you want. At a fixed threshold, a louder input can make a compressor apply more gain reduction. More input can also drive a saturator harder. If an analogue-modelled plug-in specifies a nominal input level, check its manual for the recommended setting. A reading of 0 VU depends on the meter’s calibration. For example, the Waves VU Meter reads 0 VU for a −18 dBFS reference tone at its default setting.
Once you have a setting you like, loop the same passage and switch the plug-in in and out. Adjust its output or make-up gain until the two versions sound about equally loud. Listen for what you wanted to change, such as whether the compressor steadies the vocal without dulling consonants. The peaks may differ after compression, even when the two versions sound equally loud.
4. Balance the tracks and check what reaches the buses
Use the track faders to set the balance in the full mix. A hi-hat fader can sit well below unity (0 dB of gain) if the hi-hat belongs low in the mix. Several tracks can sum to a much higher level on their group bus than you see on any individual channel. Play a busy section and check the bus meters and any gain-reduction meters.
If the drum bus compressor starts flattening the snare when the toms come in, try lowering the level before the compressor or revisiting its threshold. If you like the compression and the whole kit is simply too loud in the mix, lower the level after the compressor.
5. Check the master output and export
Play the loudest section and check the meter after the master processing and final output gain. If it goes into the red, find out where the signal first becomes a problem.
- The mix is clean until the final output. A floating-point mixer can carry an internal signal above 0 dBFS without clipping it. Lower the master fader or use a final gain plug-in after the mix-bus processing to bring the level down before it reaches your interface or a fixed-point export.
- The distortion starts earlier. Check the recording and the inputs and outputs of suspect plug-ins. If a plug-in is overloading, reduce the gain ahead of it or change its drive setting. Turning down the master will make any distortion already in the signal quieter.
For a mix going to mastering, follow the engineer’s delivery instructions. Peaks around −6 to −3 dBFS leave a practical margin if no target is specified. If a mix-bus limiter is part of the sound, ask the engineer whether they want a version with it, a version without it, or both. Check the exported file itself for unexpected clipping before sending it. See Sonalix’s mix review guide for the export checks.