Skip to content

How to prepare a mix for mastering

Send feedback

Last updated 4 min readTags:MasteringDelivery

Check your mix before mastering, decide which mix-bus processing to keep, and export a stereo WAV at the right sample rate and bit depth.

Send your approved mix as a stereo WAV at the session’s sample rate. A 24-bit WAV is a good default unless your mastering engineer asks for another format. Switch off export normalisation, leave a few decibels of peak headroom and listen to the exported file before sending it.

Check the mix in your session

  • Balance. Listen to the busiest section. If the kick swallows the bass or the vocal gets lost, fix the tracks involved. A change to the stereo mix will affect other sounds in the same frequency range.
  • Noise and edits. Listen through the quieter sections for unwanted hum, clicks and abrupt edits. Add short crossfades where needed.
  • Mono. Sum the mix to mono and check that important parts still come through. If a part all but disappears or the bass drops sharply, check any stereo widening or layered tracks involved.
  • Start and end. Check that the export range includes the first sound and the full decay of the last note, delay or reverb tail. Keep any intentional fades.

For a fuller listening pass, see how to review a mix.

Decide what stays on the mix bus

Keep EQ, compression or saturation that contributes to the sound you approved. If a final limiter or clipper was there to make the rough mix louder, bypass it for the mastering export. Listen again after bypassing it and check the output peaks, which may now be higher.

If you mixed into the limiter and bypassing it changes the balance or feel of the track, send both versions. Label the processed version as your approved reference and the other as the version with the limiter bypassed. Follow your engineer’s instructions if they ask for a particular mix-bus setup.

Leave headroom without changing the balance

Check the highest sample peak across the whole song. If the engineer specifies a peak level, follow it. Otherwise, peaks around −6 to −3 dBFS give you a practical margin below 0 dBFS. A quieter mix is fine, and there’s no LUFS target you need to hit before mastering.

If the clean mix bus is simply too loud at the output, lower the gain after the last processor. If a track or plug-in is already distorting unintentionally, reduce the level where the clipping occurs. Turning down the output will make that distortion quieter, but it will still be in the file.

Export the stereo mix

Use your engineer’s delivery settings if they’ve provided them. Otherwise, start here.

Setting What to use
Format Stereo WAV. AIFF is also suitable if the engineer accepts it.
Sample rate The session’s sample rate. If you mixed at 48 kHz, export at 48 kHz.
Bit depth 24-bit PCM, or 32-bit float if the engineer prefers it.
Normalisation Off.
Dither Off for 32-bit float. For 24-bit PCM, follow the engineer’s instructions if supplied.

Dither adds very low-level noise to reduce quantisation distortion. Some engineers request an undithered 24-bit file. If your engineer has no preference and your DAW is reducing to 24-bit PCM, standard triangular dither is suitable. Leave noise shaping off for a file that will be processed again. Ableton’s export manual

Play the exported file from start to finish. Check the opening, the end of the tail and any places where you made edits. Confirm the sample rate, bit depth and peak level on the exported file. If it sounds different from the session, compare at matched playback levels with the same mix-bus processing in use.

Send clearly labelled files and a short note

Put the artist, song and mix version in the filename, for example Artist_Song_Mix-v03.wav. If you include a louder reference, use a name such as Artist_Song_Mix-v03_Limited-reference.wav.

Tell the engineer which release formats you need, what you like about any reference tracks, and which deliberate effects to preserve. Give a timestamp for any concern you want them to hear. A short note is enough.

The main WAV is the version with the final limiter bypassed. The reference shows the drum impact we approved. Please keep the vocal distortion at 2:14. We need a streaming master and a CD master.

Was this page helpful?

    Type to search titles, headings and summaries.