Bus compression: what glue means and how to set it
Last updated 7 min readTags:MixingCompressionDynamics
Learn what bus compression does, how to set attack and release, and how to judge whether it improves your mix without losing drum impact.
Bus compression applies compression to several tracks together, such as a drum group, a vocal stack or the whole mix. When the compressor reduces gain, it turns down everything routed through that bus.
Engineers often call gentle bus compression glue. It can make a group sound more consistent because the parts share the same changes in level. It can also soften drum hits, exaggerate pumping or reduce the contrast between sections.
For a first mix-bus test, try a 2:1 ratio, 10–30 ms attack and Auto release, with about 1–2 dB of gain reduction in louder passages. Compare at matched loudness before deciding whether to keep it.
What does glue compression actually do?
A bus is a channel that receives audio from other channels. A drum bus might receive the kick, snare, toms and overheads; the mix bus receives the full mix.
A compressor on that channel responds to the combined signal. A kick hit may trigger gain reduction, but the compressor also turns down the vocal, guitars and other sounds passing through it at that moment. As the reduction eases, those sounds return to their previous level together.
This shared response can make drum hits and their room sound feel more connected, or make a backing-vocal stack more even. On a full mix, the benefit may be subtle. Listen for a more consistent accompaniment without a loss of impact or unwanted dips in the vocal.
“Glue” describes the intended effect, rather than a separate compression process. You can try it with a suitable compressor already in your DAW; a plug-in with “bus” or “glue” in its name is not essential.
How to set a mix-bus compressor
If you are new to bus compression, begin with a reasonably balanced mix. Insert a stereo compressor on the mix bus, before any final limiter, and loop a busy passage.
| Control | Starting point | What to adjust by ear |
|---|---|---|
| Ratio | 2:1 | Increase only if you want firmer control above the threshold |
| Attack | 10–30 ms | Lengthen it if kick and snare hits lose their initial impact |
| Release | Auto, or roughly 100–300 ms | Adjust if the mix dips or swells awkwardly after hits |
| Threshold | About 1–2 dB of reduction in louder passages | Raise it if the mix sounds flattened or over-controlled |
| Make-up gain | Match the bypassed loudness | Recheck after changes to compression |
| Dry/wet, if present | 100% wet for this test | Leave it here while you learn what the main controls do |
These are conservative audition settings, not targets every mix must meet. Different compressors can respond differently at the same displayed settings.
Set the threshold first. Lower it until the compressor responds to the passage. Watch the gain-reduction meter, then listen to the drums, vocal and accompaniment together. There is no need to make every beat produce the same reading.
Adjust the attack. Attack controls how quickly gain reduction builds. It is not a fixed pause during which the compressor does nothing. A slower attack often preserves more of the initial drum hit; a faster attack controls it more firmly. Neither is automatically better.
Adjust the release. Release controls how quickly gain reduction eases. If the accompaniment swells abruptly after each kick, try a longer release or less compression. If it stays suppressed through the next hit, try a shorter release. The meter need not return fully to zero between every beat.
Auto release adapts to the incoming signal. Try it first if available, but switch to a manual setting if its recovery sounds awkward.
When kick and bass make the whole mix duck
A strong low end can trigger substantial compression. You may hear the vocal or cymbals dip whenever the kick hits, even though their own levels have not changed.
A sidechain high-pass filter reduces low frequencies in the compressor's detector signal. The compressor then responds less strongly to those frequencies. The filter does not directly remove bass from the audio output, but it changes the compression you hear.
If your compressor has this control, try a cutoff around 60–100 Hz and adjust it while listening. Check whether the unwanted dips improve and whether the bass remains controlled. A higher cutoff is not necessarily better.
If the kick or bass is also too loud with compression bypassed, fix its level or processing in the mix. The kick and bass guide covers that balance. A bass-driven compressor response alone does not prove that the low end is wrong.
How to tell whether it helped
Use make-up gain or an output trim to bring the compressed version close to the bypassed loudness. Compare the same passage in both states. A loudness meter can assist, but do not match peak readings: compression changes the relationship between peaks and average level.
Listen for specific changes:
- Drum impact: do the kick and snare still have the attack you want?
- Vocal stability: does the vocal remain clear, or dip with the drums?
- Sustains and ambience: are tails more audible, or do they swell distractingly?
- Section contrast: does the chorus still sound appropriately bigger than the verse?
Check a quieter passage as well as the loudest one. Settings that suit a dense chorus may behave quite differently in a sparse verse.
If the improvement disappears once loudness is matched, bypass the compressor. A mix does not need bus compression merely because the channel is available.
Drum buses, vocal groups and stereo linking
Choose the bus according to what needs attention. If the drums need firmer control but the vocal already sits well, try the drum bus first. A vocal-group compressor can smooth a stack, though a single word or singer that jumps out may still need channel-level adjustment.
Group processing also affects what reaches the mix-bus compressor. After changing a drum or vocal bus, recheck the full mix. Several small stages of compression can still remove too much dynamic contrast.
On a stereo bus, stereo linking determines how closely the left and right channels share gain reduction. Full linking is a useful starting point for a stable stereo image. With independent compression, a loud sound on one side can cause that side to turn down more than the other. Listen for unwanted shifts in position if you reduce the link amount.
Common problems
| What you hear | What to try |
|---|---|
| Kick and snare lose impact | Slow the attack, reduce gain reduction, or both |
| Vocal dips on kick hits | Try the sidechain high-pass filter; check the low-end balance |
| Mix swells abruptly after hits | Lengthen release or reduce gain reduction |
| Mix remains suppressed between hits | Shorten release, try Auto, or raise the threshold |
| Chorus no longer sounds bigger | Check whether louder sections receive too much compression |
| Stereo image shifts | Increase stereo linking if the compressor offers it |
Should you add it before mastering?
Bus compression can be part of the mix's sound. You can introduce it early and mix through it, or try it once the balance is established. Either way, revisit its settings after substantial mix changes.
Heavy compression is difficult to undo. If a mastering engineer is involved, discuss the processing and provide an alternative export if requested. Simply bypassing a compressor you have mixed through may change the balance and peak level, so check that version before sending it.
Bus compression also does not guarantee an output ceiling. Check the exported file's true peak; gentle compression is no substitute for peak control when a delivery specification requires it.
Sources
- Ableton Live manual: Glue Compressor, for group processing, attack, release and sidechain controls.
- Waves: How to use an SSL buss compressor, for example mix-bus settings and level-matched comparisons.
- SSL Bus Compressor 2 user guide, for bus-compressor controls and sidechain filtering.
- FabFilter: Side chain section, for stereo linking and detector controls.