Skip to content

Pan laws explained: -3, -4.5 and -6 dB

Send feedback

Last updated 5 min readTags:MixingStereoFundamentals

Learn what -3, -4.5 and -6 dB pan laws change, why a mono source changes level as you pan, and when to leave your DAW's setting alone.

Move a mono guitar from hard left to the centre and its loudness may change, even though you have not touched the fader. The pan law determines how the left and right channel gains change during that move.

The familiar -3, -4.5 and -6 dB settings describe the reduction applied to each output channel at the centre, relative to the hard-panned level. They offer different ways to keep the source's level reasonably consistent as it moves.

For an existing mix, keep the setting you used to balance it. For a new project, your DAW's default is usually a sensible starting point; check the result in stereo and mono before deciding to change it.

What a pan control does

On a mono track, an ordinary pan control distributes one signal between the left and right outputs. Hard left sends it to the left output only. At the centre, it sends an equal copy to both.

If both copies kept the full hard-panned level, the source could sound louder in the middle. With a conventional -3 dB law, each output receives the centred signal at 3 dB below the hard-panned level.[1]

Suppose a steady tone reads -12 dBFS on the left output when panned fully left. At the centre, a -3 dB law would put it at approximately -15 dBFS on each output. It now plays through both.

What the three pan laws change

This table compares the same mono source at the same fader setting, first hard-panned and then centred. It assumes the panner leaves the hard-panned signal at unity gain, with no boost or gain compensation.

Pan law Amplitude sent to each channel at centre Centre level in mono, relative to hard-panned
-3 dB About 71% of the original About 3 dB higher
-4.5 dB About 60% About 1.5 dB higher
-6 dB About 50% Approximately unchanged

The mono figures follow from adding the two in-phase copies.[2] Any fixed reduction in the mono-summing control affects both pan positions equally, so the relative differences remain.

Constant-power panning keeps the sum of the two channel powers constant throughout the pan range, with approximately -3 dB per channel at centre. Linear, equal-gain panning keeps the sum of the two gains constant, with approximately -6 dB at centre. The -4.5 dB law is a compromise between these approaches.[2]

These figures do not predict perceived loudness exactly. Speaker interaction depends on frequency, room acoustics and listening position; it does not produce a fixed 3 dB increase. The centre figure also does not fully describe the panning curve between the centre and either edge.

Why the mono result is different

A centred mono source produces identical, in-phase copies in the left and right channels. When those channels are summed to mono, the copies add together. Two equal, in-phase signals produce about 6 dB more level than either copy alone.

Under a -3 dB law, each copy has been reduced by 3 dB, so their sum is about 3 dB above the hard-panned source's mono level. Under a -6 dB law, the two half-amplitude copies add back to approximately the original level.

Choosing -6 dB does not automatically preserve a finished mix's stereo balance in mono. You still set track levels by ear, and separate performances, stereo effects and phase relationships affect the result.

For the listening checks, see mono compatibility.

Which pan law should you use?

If you are choosing from scratch, -3 dB constant-power panning is a reasonable starting point for stereo work. Try -4.5 dB if the centre sounds too prominent as you pan. Linear -6 dB panning is useful when a mono source must retain its summed level during pan moves.

Choose before you make detailed level decisions, then check the mix in mono.

If a vocal becomes too prominent against wide guitars in mono, compare their balance in both modes and adjust the relevant tracks. A project-wide pan-law change may alter many other levels at once.

What happens if you change it halfway through a mix?

With conventional, uncompensated settings, a switch from -3 to -6 dB lowers centred mono tracks by another 3 dB per output. Hard-panned tracks stay at the same level. Partly panned tracks change according to the panning curve.

Your vocal, kick and bass could therefore become quieter relative to wide guitars. Save a copy before experimenting, and reassess the balance afterwards.

Some DAWs also offer compensated options. Logic Pro's -3 dB Compensated setting, for example, leaves the centre at unity gain and boosts the hard-panned output by 3 dB. The centre-to-edge relationship is similar, but the absolute output levels differ.[1]

Once exported, a stereo file contains the resulting left and right signals. Playback does not apply your project pan-law setting again.

Mono panning and stereo balance are different

A centred stereo track does not automatically become dual mono. A conventional balance control changes the relative levels of its existing left and right channels. A stereo panner may reposition those channels within the stereo field.[3]

Check the control type before applying these mono examples. See stereo balance for more detail.

A quick listening check

  1. Loop a mono recording and leave its fader fixed.
  2. Move it slowly from hard left through the centre to hard right. Listen for an unwanted rise or dip in level.
  3. Repeat through your mono monitoring control. Keep the monitoring level fixed during the sweep.
  4. Return to the full mix and check the source against the other instruments.

If a pan move changes the level more than you want, try another law early in the project, or use volume automation to correct that particular move.

Sources

  1. Apple: General Audio project settings in Logic Pro. Centre attenuation and compensated pan-law options.
  2. Carnegie Mellon University: Loudness Concepts & Panning Laws. Linear, constant-power and -4.5 dB panning; the table's rounded figures are calculated from the channel gains.
  3. Apple: Set channel strip pan or balance positions. Mono pan, stereo balance and stereo pan controls.

Was this page helpful?

    Type to search titles, headings and summaries.