How to export stems and check that they sum to your mix
Last updated 4 min readTags:MasteringDelivery
Export aligned WAV stems with their effects and automation intact. Learn what to do with mix-bus processing and check your stems with a null test.
A stem is a submix of related tracks exported as one audio file. A drum stem might contain the kick, snare, overheads and percussion. Multitracks give the recipient a separate file for each track, with or without processing as agreed.
To export stems, use the same start and end points for every file and keep each group at its mix level. To check that the files add up, compare their sum with a stereo bounce taken from the same point in the signal path.
Decide what goes in each stem
Ask the recipient for their preferred grouping and file format. For stem mastering, drums, bass, instruments and vocals are a sensible starting point. Add a stem for shared effects if you need one. A remixer might want the kick and synth bass in separate files. For a live show, the click may need its own output. For sync, use the delivery spec to decide how to group the parts and which alternate mixes to supply.
Export the stems
- Set one export range. Start every file at the same point, often bar 1 or 00:00. Keep any leading silence and use the same end point, after the last reverb or delay tail.
- Keep the group processing and automation. Export each group bus with its inserts, fader moves and panning intact. If the kick triggers a compressor on the bass, keep the kick feeding the sidechain during the bass export. Only the bass should reach that file. If soloing the bass cuts the trigger, capture the group outputs while the full session plays.
- Account for every effects return. Include a dedicated vocal delay in the vocal stem. If drums and vocals share a reverb, export the wet return once as a separate stem with both sends active. Check that your export settings do not also print that return into the group files.
- Export before the mix-bus chain if the stems need to sum cleanly. A compressor or limiter reacts to the combined signal on the mix bus. It will respond differently if you feed it one stem at a time. Bounce a stereo mix from the same point as the stem sum, before that processing, for your null test. If the mix-bus chain is part of the sound, send the approved stereo mix as well and explain what was on the bus.
- Export WAV files at the requested settings. If there is no spec, use 24-bit stereo WAV at the session sample rate, with normalisation off. Check for clipping in both the individual files and their sum. If the level is too high at export, apply the same gain trim to all stem outputs and the matching stereo bounce. If a track or plug-in is already clipping inside the session, fix it there first.
Run a null test against the matching stereo bounce
- Import the stems and the matching stereo bounce into an empty session at the export sample rate. Line them up at the same sample position, disable automatic warping, leave the faders at 0 dB and bypass output processing.
- Invert the polarity of both channels of the stereo bounce. Play it alongside all the stems.
- Listen to the output. If the signals match sample for sample, they cancel to silence. Anything you hear is the difference between the stem sum and the stereo bounce.
| What remains | What to check |
|---|---|
| A recognisable instrument or effect | A group or effects return may be missing, duplicated or at the wrong level. |
| A thin or doubled version of the mix | Check sample alignment, plug-in latency and whether the DAW stretched an imported file. |
| Bass that swells on kick hits | Check whether the kick still triggered the bass compressor during export. |
| A faint, shifting reverb or chorus | A modulated effect may have behaved differently on separate passes. Try capturing the groups and comparison bounce in one pass if your DAW supports it. |
If there is a small residue, switch between the stem sum and the stereo bounce at the same listening level. Check that the balance, effects and endings sound as intended before sending the files.
Name and deliver the files
Use names that identify the song, mix version and group, such as SongTitle_Mix03_Drums.wav. Keep the stereo reference in a separate folder so it is easy to audition without adding it to the stem sum. In a short note, give the tempo and key where useful, list any separate effects or click files, and identify which stereo bounce matches the stems.