Album loudness consistency for EPs and albums
Last updated 4 min readTags:MasteringDelivery
Balance track levels across an EP or album, check transitions and true peaks, and learn how streaming normalisation affects the sequence.
Two songs can both measure −10 LUFS integrated and still feel different in level. A song with a quiet verse and a big chorus can have the same whole-track reading as one that stays fairly loud throughout. The first song’s chorus can still sound louder than anything in the second.
Master the tracks in album order so you can hear those differences. If a quiet instrumental leads into a full-band song, the jump might be exactly what you want. If two choruses should land with similar impact and one keeps making you turn the volume down, try a small gain change.
1. Choose a reference track
Put the mixes or working masters in a DAW session in their intended order. Choose a track whose level, tone and dynamics suit most of the record. A representative song is a better starting point than the loudest or densest one. If you already have a master you like, use it as your reference.
2. Balance the tracks by ear
Leave your monitor volume fixed. Switch between comparable passages, such as two full-band choruses, and adjust each track's output gain in small steps. If a track feels too loud, try turning it down by 0.5 or 1 dB and listen again. If you're working with a mastering chain, make this trim after the limiter so the amount of limiting stays the same.
Then play the end of each track into the start of the next. An exposed vocal can feel abruptly loud after a long fade even when the two songs' main sections sit well together. Listen through to the next full section before deciding whether to change the whole track or just its opening.
3. Check what the loudness meter is showing
Use integrated LUFS to compare whole tracks and short-term LUFS to compare specific passages. Short-term loudness measures the preceding three seconds. If two songs have the same integrated reading but one chorus feels louder, compare the readings a few seconds into each chorus. That can show a difference that the whole-track figures conceal. See integrated, short-term and momentary loudness.
Record the readings if they help you keep track of revisions. A lower reading on a deliberately quiet song is worth noting so you leave the difference in place during later passes.
4. Compare tone at a matched level
Temporarily match the listening level of the passages you're comparing. If a chorus still sounds sharp, or the bass seems to recede as the next track starts, check whether the difference persists in similar parts of the arrangements. A spectrum analyser can point you towards a frequency range to listen to.
If an entire mix consistently sounds sharper than the tracks around it, try a small, broad cut and compare it with the original at matched loudness. A sparse acoustic arrangement and a dense electric one will naturally have different spectra. Restore the intended track levels after the comparison. See master equalisation.
5. Set the gaps and fades
Listen from the last phrase of one song into the first phrase of the next. Leave enough room for a reverb tail to decay if you want it to finish. Shorten the gap if the next track ought to come in while you can still feel the previous tempo. Recheck the transition after any change to either track's level or fade.
6. Listen to the exports in order
Check the final true peak of each export against your delivery ceiling, especially if you raised its gain after limiting. Play the exported files back in order without loudness normalisation or crossfade. Listen at a low volume and try a second playback system if you can. If a change in level, tone or timing distracts you, note the track and timestamp and revisit it after the run-through.
What streaming normalisation does to album levels
When Spotify applies album-level normalisation, it uses the same gain adjustment for the whole release. With album shuffle or a playlist containing tracks from different releases, it adjusts the tracks individually. Spotify for Artists' loudness normalisation guide
Apple says Sound Check can also apply a gain adjustment to the album as a whole. A quieter song keeps its relative level when album-level gain applies and may sit closer in level to other songs when playback uses track-level gain. Apple Digital Masters, ‘Loudness Normalization’ (PDF)
Set the relative levels for the album you want people to hear. To hear how a song fares on its own, audition it separately with loudness normalisation switched on.