Dynamic Range vs Loudness Range: Which Meter to Use
Last updated 7 min readTags:MasteringLoudnessDynamics
Learn how loudness range (LRA) differs from crest factor, PLR and DR readings, and which measurements to check when a mix lacks punch or section contrast.
Loudness range (LRA) describes how loudness varies across a track. Dynamic range is a broader term: it can describe changes between quiet and loud passages, the difference between peaks and average level, or the usable level range of recording equipment.
That ambiguity matters when you read a mix report. A track can have clear differences between quiet and loud sections while its drums sound heavily limited. Another can stay at a fairly consistent loudness while its drum hits remain prominent.
To interpret a dynamics reading, you need to know what the meter measures and which part of the track it covers.
Dynamic range and loudness range compared
| Measurement | What it measures | What it can help you investigate |
|---|---|---|
| Loudness range (LRA) | The spread of short-term loudness readings, after gating and exclusion of the extremes | Loudness variation across the track |
| Crest factor | Peak amplitude relative to RMS amplitude over the measured interval | The peak-to-average relationship, including changes after compression or limiting |
| Peak-to-loudness ratio (PLR) | Maximum true peak level minus integrated loudness | The relationship between the highest peak and overall loudness |
| DR reading | A meter-specific peak-to-average calculation, commonly associated with TT/MAAT meters | Comparisons of dynamics using the same DR method |
These readings are not interchangeable. A crest factor of 10 dB, a PLR of 10 and an LRA of 10 LU describe different properties of the signal.
What LRA tells you
LRA uses short-term loudness readings measured over sliding three-second windows. The calculation excludes readings below an absolute gate of −70 LUFS, then applies a relative gate 20 LU below the absolute-gated loudness. It takes the difference between the 10th and 95th percentiles of the remaining readings. The result is expressed in loudness units, or LU. [1]
Those gates and percentiles reduce the influence of silence, very quiet background sound and brief extremes. LRA therefore differs from simply subtracting the quietest moment from the loudest.
It also does not identify where a change occurs. An LRA reading alone cannot tell you whether the final chorus is louder than the first. For that, follow the short-term loudness readings through both sections.
See the LRA reference for more on the calculation.
What crest factor and PLR tell you
Crest factor compares peak amplitude with RMS amplitude. In decibels, it is calculated as:
Crest factor = 20 × log10(peak amplitude ÷ RMS amplitude)
RMS describes the signal's average energy over the measurement interval; it is not perceptually weighted loudness. The interval matters: crest factor measured over a chorus can differ considerably from crest factor measured over the whole song.
PLR uses integrated loudness instead of RMS. For example, a track with a maximum true peak of −1 dBTP and integrated loudness of −11 LUFS has a PLR of 10. [2]
Both measurements can reveal changes after peak reduction, but neither is a direct measure of punch. A high reading might come from prominent drum attacks, one unusually large peak, or differences between quiet and loud passages. A low reading might reflect heavy limiting, or simply a sustained sound with few prominent peaks.
Where DR meters fit
A DR reading is another peak-to-average measure, with its own calculation. MAAT describes its method as comparing peaks against an average derived from the loudest 20% of events. [3]
Use it for comparisons made with the same method. Do not read DR10 as equivalent to 10 LU of LRA or 10 dB of crest factor.
Why one mix can produce very different readings
Consider a song with a quiet verse and a much louder chorus. Within the chorus, a limiter reduces the drum peaks heavily.
The track may still have a substantial LRA because the verse and chorus differ in loudness. That does not establish whether the chorus retains the drum sound you want. Compare the chorus with and without the limiter, at matched playback loudness, and check its peak-to-average readings alongside what you hear.
Now consider a dance track with little change in loudness between sections. Its LRA may be low, even though the kick and snare have distinct attacks. There may be no need to create larger section-level changes if the arrangement works as intended.
Whole-track crest factor and PLR can also conceal local problems. A quieter introduction may lower the track's average level and increase the overall peak-to-average gap, while a heavily limited chorus still sounds flat. Measure the chorus separately before drawing a conclusion about it.
Which meter should you check first?
Start with the audible problem, then choose the measurement that can clarify it.
| What you hear | Check first | What to investigate |
|---|---|---|
| The chorus does not feel bigger than the verse | Short-term loudness through both sections | Level differences, arrangement, instrumentation and tonal balance |
| Quiet passages are difficult to hear | Short-term loudness through those passages; LRA for the whole track | Section automation, vocal or lead balance, and the intended listening conditions |
| Drum attacks lose definition after processing | Crest factor or a local peak-to-average reading over the affected passage | Limiter input, compressor attack and release, clipping, and processing on the drums themselves |
| The whole track feels overly dense | Peak-to-average readings in representative passages, plus LRA | Whether the problem occurs within sections, between sections, or both |
| A streaming service reduces playback level | Integrated loudness and true peak | Loudness normalisation, rather than section contrast |
A chorus can feel bigger because it becomes brighter, wider or more densely arranged, even with little increase in measured loudness. Likewise, a drum can lose definition because other instruments mask it. The meter helps test a possible explanation; it does not establish the cause by itself.
How to use the readings when you revise a mix
If you suspect the limiter, compare the same loud passage with and without it. Lower the louder version's monitoring level so that both play at a similar perceived loudness. Listen for changes in drum attack, distortion and the balance between the drums and sustained instruments.
If the processed version loses impact, try reducing the limiter input by 1–2 dB as an initial test. Match playback loudness again and compare. A rise in crest factor or PLR supports the observation that the peak-to-average relationship changed; your listening comparison determines whether the result suits the track.
If the problem is a weak transition into the chorus, compare short-term loudness across the transition. Review the arrangement and section automation before adding more compression to the mix bus. A whole-track LRA value cannot tell you which fader to move.
After a useful change, measure the complete export for overall context. Keep the meter, settings and measured passages consistent when you compare versions. The dynamic range control guide explains the processing options in more detail.
Is there a good dynamic range or LRA for music?
There is no single target that establishes whether a mix is good. A dense electronic track and a sparse acoustic recording need not produce similar readings. The EBU's production guidance likewise makes clear that LRA cannot guarantee mix quality and does not set one maximum value for every programme. [4]
Choose reference tracks with a similar style and arrangement. Compare them at matched playback loudness, then use measurements to investigate the differences you hear. Check equivalent passages as well as complete tracks.
Treat LRA from short clips cautiously. The EBU warns that short-form material may provide too little information for a meaningful LRA result. A brief chorus loop is more useful for local listening and peak-to-average comparisons than for judging the loudness range of a complete song. [4]
If you want to check your own track, analyse your mix with Sonalix. Use the report to identify passages and processing choices to review, then compare each revision by ear.
Sources
- EBU Tech 3342: Loudness Range, sections 2–3.1. Definition, three-second analysis windows, gating and percentiles.
- Klangfreund Multimeter manual, “PLR and PSR”. PLR definition.
- MAAT DRMeter user manual. Vendor description of the DR measurement method.
- EBU Tech 3343: Guidelines for Production of Programmes in Accordance with EBU R 128, sections 3.3 and 11.2.2. Interpretation of LRA and limitations for short-form material.