Skip to content

Goniometers and vectorscopes: how to read the display

Send feedback

Last updated 7 min readTags:MixingStereoAnalysis

Learn what goniometer shapes mean, how to check stereo correlation, and how to find sounds that lose level or change tone in mono.

A goniometer shows the relationship between the left and right channels of a stereo signal. Its moving trace can reveal a narrow image, a channel imbalance or content that may cancel when the channels are summed to mono.

On the common display with mono on the vertical axis, a vertical line means the channels are identical. A horizontal line means they are equal in level with opposite polarity. Most stereo music produces a changing pattern between these extremes.

Use the display to identify passages worth checking. The shape alone cannot tell you whether the mix sounds good or which instrument caused a problem.

Are goniometers and vectorscopes the same thing?

In audio plug-ins, goniometer, vectorscope and phase scope often refer to similar stereo displays. However, some vectorscopes offer several views. A conventional Lissajous view plots the channel amplitudes against one another; polar views represent the information differently.[1]

The shape descriptions below refer to the conventional view with centred mono shown vertically. Check your plug-in's labels and display mode before applying them.

How to read the main shapes

Shape What it indicates What to check
Straight vertical line Identical left and right signals Expected for centred mono material
Thin line tilted away from vertical The same waveform at different levels in each channel Panning or channel balance
Line along a labelled left or right diagonal Signal in only that channel Intended hard panning, or a missing channel
Changing cloud around the vertical axis Differences between the channels Whether the width suits the arrangement
Strong spread towards the horizontal axis Content with opposing polarity between channels Changes in level or tone in mono
Straight horizontal line Equal-level signals with opposite polarity Complete cancellation when summed to mono

These patterns describe the channel relationship, rather than fixed grades of stereo quality.[2]

Vertical and narrow patterns

A centred mono vocal produces a vertical line. The same vocal panned to one side still produces a line, but it tilts towards that channel's axis. The tilt reflects the level difference between channels; it does not mean the vocal has acquired independent stereo detail.

A full mix may have a strong vertical pattern because the vocal, kick and bass dominate its level. Quieter guitars, cymbals and ambience can still be wide.

A wider cloud

Different performances, stereo microphones and effects can all spread the trace away from the vertical axis. The cloud changes as the arrangement changes. A chorus with extra guitars and a wide pad may look broader than a sparse verse.

There is no standard cloud shape to reproduce. Zoom, persistence and display mode affect its appearance, so comparisons are most useful with the same meter settings.

Horizontal patterns

A horizontal line is the clearest case: the channels carry equal and opposite signals, so their mono sum is silence. A brief sideways extension within a complex mix is less conclusive. It might come from a reverb tail, chorus effect or widened instrument.

Listen to that passage in mono. A small change to an effect may be acceptable; a bass part or lead instrument that almost disappears needs attention. A horizontal pattern identifies a relationship between channels, but it does not establish that someone accidentally pressed a polarity button.

Check your display with known signals

When you first use an unfamiliar meter, send it a quiet mono tone or a short mono recording. Check these four conditions:

  1. Centred: identical signals in both channels should draw a vertical line.
  2. Hard left: the line should follow the left channel's diagonal axis.
  3. Hard right: it should follow the right channel's diagonal axis.
  4. Opposite polarity: return to centre, then invert one channel only. The line should become horizontal.

This is a quick orientation check. You need not repeat it for every mix. If the shapes differ, check the selected view and the signal routing before assuming a fault.

For the final test, the polarity control must affect just one channel of the stereo pair. Inverting a mono track before it is panned to the centre reverses both output channels and leaves the line vertical.

Read correlation alongside the shape

A correlation meter summarises how the channels vary together over its measurement window. It complements the picture, particularly when the trace changes too quickly to follow.

Reading Meaning
+1 Matching waveform shapes and polarity; channel levels may differ
Between 0 and +1 An overall positive relationship between the channels
Around 0 Little overall linear correlation over the measured period
Between −1 and 0 An overall negative relationship; check for cancellation in mono
−1 Matching waveform shapes with opposite polarity; equal-level versions cancel completely in mono

Positive correlation does not guarantee that every instrument survives mono playback. A loud centred kick can keep the reading positive while a quieter stereo part suffers cancellation. Conversely, a brief negative reading on an effect does not necessarily require a change.

A silent channel is a separate case. Normalised correlation is undefined when either channel has no variation; plug-ins may display a fallback value.[4] Check the channel level meters rather than interpreting a zero reading as proof of a dropout.

For more detail, see stereo correlation.

Find the source of a suspicious pattern

Place the goniometer on the stereo output and loop the passage where the pattern changes. Keep the meter before any mono monitoring switch; a meter after the switch will simply show the mono signal.

1. Listen to the mono sum

Sum left and right with your DAW or monitor controller. Listening to one channel alone does not test cancellation between them.

Keep the monitoring level reasonably consistent. Note which sound loses weight, becomes hollow or drops behind the arrangement. The loss of left/right separation is expected; a substantial change in an important part deserves investigation.

2. Isolate the track or effect

Bypass stereo wideners, short delays, chorus effects and stereo reverbs one at a time. If the suspicious pattern appears when a pad enters, check the pad and its effects first.

For recordings made with several microphones, check the relevant microphone group. Listen to the signals together as well as individually; cancellation depends on their combination.

3. Correct the cause

Confirmed cause Adjustment to try
A widening effect causes a part to lose definition in mono Reduce or bypass the effect; compare its delay and dry/wet settings
One channel was accidentally polarity-inverted Correct the inversion at that point in the routing
Microphones or related layers interfere with one another Compare their timing, polarity and relative levels
A channel is unexpectedly silent Check mutes, routing, sends and the source file
One side is consistently louder Find the dominant track or effect before changing the whole mix

Avoid automatically aligning every doubled part. Separate performances need not match sample for sample, and their timing differences may be part of the intended sound.

A conventional mid/side width control also has limits. If it only reduces the side signal while leaving the mid unchanged, it narrows stereo playback without restoring anything to the mono sum. Mid is derived from left plus right, so the cancellation is already present there.[3] Adjust the source or effect responsible when important content is missing.

4. Compare in stereo and mono

Replay the passage with and without the adjustment. Confirm that the affected part holds its place in mono and that the stereo version still sounds right. A more vertical trace is not sufficient reason to keep a change.

What a full-mix display can miss

A goniometer combines all frequencies into one picture. In a bass-heavy mix, the kick and bass may dominate the trace while the upper frequencies behave quite differently.

If the overall shape does not explain what you hear, use a frequency-selective meter or put an EQ before the analyser on a separate analysis bus. Low-pass that feed to inspect the bass; high-pass it to inspect the material above. Apply the same filter to both channels, and keep the filtered feed out of the audible mix.

Band-limited readings describe only the selected range. Return to the unfiltered mix for the final judgement, and check the sections where the arrangement changes. A narrow verse and a wide chorus can both be appropriate.

Sources

  1. iZotope Insight 2: Sound Field, for vectorscope display modes and visual interpretation.
  2. Image-Line: Wave Candy, for channel axes, panning and phase patterns.
  3. iZotope: 8 Common Mistakes in Mid/Side Mixing, for the sum/difference relationship and its implications.
  4. NumPy: corrcoef, for the normalised correlation formula; zero variance makes its denominator zero.

Was this page helpful?

    Type to search titles, headings and summaries.