Skip to content

Limiting: what a limiter does and how to set one

Send feedback

Last updated 7 min readTags:MasteringLimitingDynamics

Learn how a limiter controls peaks, what gain and ceiling change, and how to adjust lookahead and release without losing punch or distorting your mix.

A limiter reduces gain when an audio signal would exceed a set output level, called the ceiling. On a finished mix, it can control occasional peaks or raise average loudness without those peaks exceeding the ceiling.

Too much limiting can make drums less punchy, distort bass notes or cause the whole mix to dip with each kick. The aim is to control peaks while keeping the sound you want. Compare at matched loudness; a louder version can seem better simply because it is louder.

Gain, threshold and ceiling

A limiter works much like a compressor with a very high ratio. Its main controls determine when gain reduction starts and the maximum output level.

Control What it changes
Input gain Raises or lowers the signal before limiting. More gain usually means more gain reduction and higher average loudness.
Threshold Sets the level at which limiting starts. Some limiters automatically add output gain as you lower it.
Ceiling Sets the maximum output level. True peak mode controls estimated peaks between samples as well as sample peaks.

The controls vary between plug-ins. An input gain control and a threshold control can produce a similar result, but they are not interchangeable labels. Check whether your limiter adds gain automatically and whether its ceiling controls sample peaks or true peaks.

A worked example

Suppose a mix peaks at −3 dBFS. In a limiter that adds input gain and then limits to the ceiling, you add 6 dB and set a sample-peak ceiling of −1 dBFS.

Stage Level at the loudest peak
Original mix −3 dBFS
After 6 dB of input gain, before limiting +3 dBFS
Required gain reduction at that peak 4 dB
Output peak −1 dBFS

The +3 dBFS figure is an internal level before limiting; it need not mean the audio has clipped inside a floating-point plug-in.

The limiter turns the signal down around that peak, then releases the reduction. In a conventional full-band limiter, a kick can therefore turn down the vocal and cymbals at the same time. The processor does not isolate and reduce only the kick.

If the result sounds crushed, reduce the input gain or ease the threshold. Lowering the ceiling cannot restore dynamics already lost. Depending on the plug-in, it may increase gain reduction or simply lower the output.

Lookahead and release

Lookahead delays the audio briefly so the limiter can respond before a peak reaches its output. Very short settings can sound gritty, particularly on bass. More lookahead may reduce distortion, but it can also soften the initial attack of drums. Start with the default setting rather than assuming that longer is always better.

Release controls how quickly gain returns after a peak. If it is too short, bass notes can distort as the gain changes rapidly. If it is too long, a kick may leave the vocal or the next drum hit quieter than intended. Auto-release is a useful starting point where available.

Listen for the specific fault as you adjust either control. Pumping does not identify one correct release setting; it can come from excessive gain reduction, unsuitable timing or a kick that is too loud in the mix.

Sample peaks, true peaks and the ceiling

A sample-peak ceiling controls the stored samples. The reconstructed waveform can peak higher between them. A true peak limiter estimates and controls these inter-sample peaks.

Lossy encoding, such as AAC or MP3, can change peak levels again. True peak limiting before export does not guarantee that every encoded version will remain below the same ceiling.

Enable true peak limiting if your plug-in offers it. Oversampling can reduce some processing artefacts, but it is not a substitute for true peak limiting or a final measurement of the exported file.

For Spotify, the published guidance is to keep true peak below −1 dBTP, or below −2 dBTP for masters louder than −14 LUFS integrated.[1] Treat these as Spotify's recommendations; check the requirements for your intended delivery format.

How to set a limiter on a finished mix

  1. Place it after processors that change the sound or level. Keep a loudness and true peak meter after it. Avoid adding gain with a downstream fader or export setting.
  2. Choose a ceiling and enable true peak mode. Use the delivery guidance above where relevant. If true peak limiting is unavailable, leave headroom and check the export with a true peak meter.
  3. Play the loudest section and increase the amount of limiting gradually. Raise input gain or lower the threshold, according to the plug-in. Start with roughly 1–3 dB of gain reduction on the strongest peaks, then listen. This is a starting point, not a pass/fail limit.
  4. Check drums, bass and vocals. Listen for weaker drum attacks, new grit on sustained bass notes, or a vocal that dips when the kick hits. Reduce the amount of limiting first. Adjust lookahead or release if the problem remains.
  5. Compare at matched loudness. Turn down the processed version with a separate comparison trim or gain-match function. Leave the limiter settings fixed during the comparison.
  6. Listen through the whole track and measure the export. Check that the chorus still lifts and quieter sections recover naturally. Measure integrated LUFS and true peak on the bounced file. If peaks exceed the intended maximum, check true peak mode, downstream gain and sample-rate conversion, then adjust and export again.

If one kick or snare repeatedly causes heavy reduction, lower that sound or control its peaks on its own track. This can preserve more of the mix than asking the final limiter to reduce everything whenever it hits.

How loud should you make it?

Use LUFS to measure loudness, but decide how much limiting sounds right at matched playback level.

With Spotify's Normal setting, a track measured at −8 LUFS integrated is typically turned down by about 6 dB towards −14 LUFS. That adjustment does not undo the limiting. Spotify also has other playback settings, and its web player and some third-party devices do not use normalisation.[1]

A normalisation target is not a compulsory mastering target. Dense limiting may suit the music; it may also flatten a mix that needs more contrast. Compare with a suitable reference at matched loudness and stop when further limiting makes the sound worse.

Common limiting problems

What you hear or measure What to check What to try first
Drums lose their attack Heavy reduction on each hit Reduce input gain or ease the threshold.
Bass becomes gritty Excessive reduction, short release or short lookahead Reduce limiting, then compare slower timing settings.
The mix dips with each kick Kick level and the gain-reduction recovery Lower the kick slightly; compare release or auto-release settings.
The chorus no longer lifts More reduction in the chorus than the verse Ease the limiting and check the section balance.
Exported true peak exceeds the intended ceiling True peak mode, downstream gain and export conversion Check the signal path and lower the ceiling if necessary.

Heavy limiting often reduces crest factor, the difference between peak and RMS level. A low reading alone does not prove over-limiting; the original sounds and arrangement also affect it. Use the measurement alongside what you hear.

Sources

  1. Spotify for Artists: Loudness normalisation
  2. Ableton Live manual: Limiter, for an example of input gain, ceiling and maximiser controls.
  3. FabFilter Pro-L 2: Advanced settings, for lookahead and release behaviour in Pro-L 2.
  4. FabFilter Pro-L 2: Recommended workflow, for true peak limiting and output settings.

Was this page helpful?

    Type to search titles, headings and summaries.